You can increase your computer memory by installing memory modules on the system board.
Your computer supports DDR2 memory. For additional information on the type of memory supported by your computer, see the technical specifications for memory.
DDR2 Memory Overview
DDR2 memory modules should be installed in pairs of matched memory size and speed. If the DDR2 memory modules are not installed in matched pairs, the computer will continue to operate, but with a slight reduction in performance. See the label in the upper-right corner of the module to determine the module's capacity.
NOTE: The module's capacity label can also be seen in the upper-left corner of the module.
NOTE: Always install DDR2 memory modules in the order indicated on the system board.
The recommended memory configurations are:
A pair of matched memory modules installed in DIMM connectors 1 and 2
or
A pair of matched memory modules installed in DIMM connectors 1 and 2 and another matched pair installed in DIMM connectors 3 and 4
NOTICE: Do not install ECC memory modules.
If you install mixed pairs of PC2-4200 (DDR2 533-MHz) and PC2-5300 (DDR2 667-MHz) memory, the modules function at the speed of the slowest module installed.
Be sure to install a single memory module in DIMM connector 1, the connector closest to the processor, before you install modules in the other connectors.
1
matched pair of memory modules in DIMM connectors 3 and 4 (black securing clips)
2
matched pair of modules in DIMM connectors 1 and 2 (white securing clips)
NOTE: Memory purchased from Dell is covered under your computer warranty.
NOTICE: If you remove your original memory modules from the computer during a memory upgrade, keep them separate from any new modules that you may have, even if you purchased the new modules from Dell. If possible, do not pair an original memory module with a new memory module. Otherwise, your computer may not start properly. You should install your original memory modules in pairs either in DIMM connectors 1 and 2 or DIMM connectors 3 and 4.
Addressing Memory Configurations
If using a 32-bit operating system such as Microsoft® Windows® XP, your computer will support a maximum of 2 GB of memory. If you are using a 64-bit operating system, your computer will support a maximum of 8 GB (2-GB DIMMs in each of the four slots) of memory.
Installing Memory
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide.
NOTICE: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface on the computer chassis.
Lay the computer on its side so that the system board is on the bottom of the inside of the
computer.
Press out the securing clip at each end of the memory module connector.
1
memory connector closest to processor
2
securing clips (2)
3
connector
Align the notch on the bottom of the module with the crossbar in the connector.
1
cutouts (2)
2
memory module
3
notch
4
crossbar
NOTICE: To avoid damage to the memory module, press the module straight down into the connector while you apply equal force to each end of the module.
Insert the module into the connector until the module snaps into position.
If you insert the module correctly, the securing clips snap into the cutouts at each end of the module.
Close the computer cover.
NOTICE: To connect a network cable, first plug the cable into the network port or device and then plug it into your computer.
Connect your computer and devices to electrical outlets, and turn them on.
Right-click the My Computer icon and click Properties.
Click the General tab.
To verify that the memory is installed correctly, check the amount of memory (RAM) listed.
Removing Memory
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide.
NOTICE: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface on the computer chassis.
Press out the securing clip at each end of the memory module connector.
Grasp the module and pull up.
If the module is difficult to remove, gently ease the module back and forth to remove it from the connector.
Cards
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
NOTICE: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface on the computer.
Your computer provides the following slots for PCI and PCI Express cards:
Three PCI card slots
Two PCI Express x16 card slots (can be used in a dual-graphics configuration)
NOTE: If a graphics card is installed in each of the PCI Express x16 card slots in the dual-graphics configuration, the PCI Express x1 card slot is not accessible for use.
One PCI Express x1 card slot
1
PCI card
1
PCI Express x16 card
2
PCI Express x16 card slot
3
PCI Express x1 card
4
PCI Express x1 card slot
Removing a PCI Express Graphics Card from a Dual Configuration
NOTE: This section regards dual configurations of PCI Express graphics cards only. For removal of any other type of PCI or PCI Express cards, see "Removing PCI and PCI Express Cards."
Gently securing both graphics cards with one hand, remove the graphics card bridge with your
other hand by pulling it up and away from the computer. Set it aside.
1
graphics card bridge
2
power connectors (2)
3
dual-PCI Express graphics cards
Disconnect the power cable connected to the card.
Press the lever on the card retention arm and raise the retention arm.
1
lever
2
retention arm
3
edge connector
4
card connector
Pull the securing tab (if present), grasp the card by its top corners, and ease it out of its
connector.
If you are not replacing the card, install a filler bracket in the empty card-slot opening.
NOTE: Installing filler brackets over empty card-slot openings is necessary to maintain FCC certification of the computer. The brackets also keep dust and dirt out of your computer.
NOTE: The graphics card bridge is unnecessary in a single card configuration.
Before you lower the retention arm, ensure that:
The tops of all cards and filler brackets are flush with the alignment bar.
The notch in the top of the card or filler bracket fits around the alignment guide.
NOTICE: Do not route card cables over or behind the cards. Cables routed over the cards can prevent the computer cover from closing properly or cause damage to the equipment.
Press the retention arm into place, securing the card(s) in the computer.
1
filler bracket
2
alignment guide
3
alignment bar
4
retention arm
NOTICE: To connect a network cable, first plug the cable into the network port or device and then plug the cable into the computer.
Replace the computer cover, reconnect the computer and devices to electrical outlets, and
then turn them on.
Installing PCI Express Graphics Cards in a Dual Configuration
NOTE: This section regards dual configurations of PCI Express graphics cards only. For installation of any other type of PCI or PCI Express cards, see "Installing PCI and PCI Express Cards."
The PCI Express x1 card slot is not available for use if a graphics card is installed in each of the PCI Express x16 card slots in the dual-graphics configuration. If you are upgrading from a single graphics to a dual-graphics configuration, you will need to remove any card installed in the PCI Express x1 card slot. See "System Board Components" to locate the PCI Express x1 card slot. To remove a PCI Express card, see "Removing PCI and PCI Express Cards."
NOTICE: For information about upgrading your system to use NVIDIA SLI (Scalable Link Interface) dual-graphics technology, see the Dell website at support.dell.com.
To learn more about NVIDIA SLI (Scalable Link Interface) dual-graphics technology, see "NVIDIA SLI Dual Graphics Technology" in your Owner's Manual.
Press the lever on the card retention arm and raise the retention arm.
1
filler bracket
2
retention arm
3
lever
4
PCI card
5
edge connector
6
card connector
If you are upgrading to a dual-graphics configuration, remove the filler bracket to create a
card-slot opening.
If you are upgrading to a dual-graphics configuration and have a card installed in the PCI
Express x1 card slot, remove the card. See "Removing PCI and PCI Express Cards."
Prepare the card for installation.
See the documentation that came with the card for information on configuring the card, making internal connections, or otherwise customizing it for your computer.
Position the card so that it is aligned with the slot and the securing tab (if present) is aligned
with the securing slot.
1
PCI Express x16 card
2
PCI Express x16 card slot
3
securing tab
NOTICE: Ensure that you release the securing tab to seat the card. If the card is not installed correctly, you may damage the system board.
Gently pull the securing tab (if present) and place the card in the connector. Press down
firmly and ensure that the card is fully seated in the slot.
1
not fully seated card
2
fully seated card
3
alignment guide
4
alignment bar
5
bracket within slot
6
bracket caught outside of slot
Before you lower the retention arm, ensure that:
The tops of all cards and filler brackets are flush with the alignment bar.
The notch in the top of the card or filler bracket fits around the alignment guide.
NOTICE: Do not route card cables over or behind the cards. Cables routed over the cards can prevent the computer cover from closing properly or cause damage to the equipment.
Press the retention arm into place, securing the card(s) in the computer.
1
filler bracket
2
alignment guide
3
alignment bar
4
retention arm
NOTICE: An incorrectly attached graphics power cable may result in degraded graphics performance.
Connect the power cable to the power connector on the card.
For information about the card cable connections, see the documentation that came with the card.
1
graphics card bridge
2
power connectors (2)
3
dual-PCI Express graphics cards
Replace the graphics card bridge, pressing firmly so that it completely covers the connector
tabs.
NOTICE: To connect a network cable, first plug the cable into the network port or device and then plug the cable into the computer.
Replace the computer cover, reconnect the computer and devices to electrical outlets, and
then turn them on.
If you are not replacing the card, install a filler bracket in the empty card-slot opening.
NOTE: Installing filler brackets over empty card-slot openings is necessary to maintain FCC certification of the computer. The brackets also keep dust and dirt out of your computer.
Before you lower the retention arm, ensure that:
The tops of all cards and filler brackets are flush with the alignment bar.
The notch in the top of the card or filler bracket fits around the alignment guide.
NOTICE: Do not route card cables over or behind the cards. Cables routed over the cards can prevent the computer cover from closing properly or cause damage to the equipment.
Press the retention arm into place, securing the card(s) in the computer.
1
filler bracket
2
alignment guide
3
alignment bar
4
retention arm
NOTICE: To connect a network cable, first plug the cable into the network port or device and then plug the cable into the computer.
Replace the computer cover, reconnect the computer and devices to electrical outlets, and
then turn them on.
Press the lever on the card retention arm and raise the retention arm.
1
filler bracket
2
retention arm
3
lever
4
PCI card
5
edge connector
6
card connector
If you are installing a new card, remove the filler bracket to create a card-slot opening.
Prepare the card for installation.
See the documentation that came with the card for information on configuring the card, making internal connections, or otherwise customizing it for your computer.
CAUTION: Some network adapters automatically start the computer when they are connected to a network. To guard against electrical shock, be sure to unplug your computer from its electrical outlet before installing any cards.
Position the card so that it is aligned with the slot and (if present) the securing tab is aligned
with the securing slot.
1
PCI Express x16 card
2
PCI Express x16 card slot
3
securing tab
NOTICE: Ensure that you release the securing tab to seat the card. If the card is not installed correctly, you may damage the system board.
Gently pull the securing tab (if present) and place the card in the connector. Press down
firmly and ensure that the card is fully seated in the slot.
If the card is full-length, insert the end of the card into the card guide bracket as you lower the card toward its connector on the system board. Insert the card firmly into the card connector on the system board.
1
not fully seated card
2
fully seated card
3
alignment guide
4
alignment bar
5
bracket within slot
6
bracket caught outside of slot
Before you lower the retention arm, ensure that:
The tops of all cards and filler brackets are flush with the alignment bar.
The notch in the top of the card or filler bracket fits around the alignment guide.
NOTICE: Do not route card cables over or behind the cards. Cables routed over the cards can prevent the computer cover from closing properly or cause damage to the equipment.
Press the retention arm into place, securing the card(s) in the computer.
1
filler bracket
2
alignment guide
3
alignment bar
4
retention arm
Connect any cables that should be attached to the card.
See the documentation for the card for information about the card cable connections.
NOTICE: To connect a network cable, first plug the cable into the network port or device and then plug the cable into the computer.
Replace the computer cover, reconnect the computer and devices to electrical outlets, and
then turn them on.
Install any drivers required for the card as described in the card documentation.
Network Adapter and Sound Card Settings
If you installed a sound card:
Enter system setup, select Integrated Audio Controller, and then change the setting to Off.
Connect external audio devices to the sound card connectors. Do not connect external audio
devices to the microphone, speaker/headphone, or line-in connectors on the back panel.
If you removed a sound card:
Enter system setup, select Integrated Audio Controller, and then change the setting to On.
Connect external audio devices to the audio connectors on the back panel of the computer.
If you installed an add-in network adapter and want to disable the integrated network adapter:
Enter system setup, select Integrated NIC Controller, and then change the setting to Off.
Connect the network cable to the add-in network adapter connectors. Do not connect the
network cable to the integrated connector on the back panel.
If you removed an add-in network connector:
Enter system setup, select Integrated NIC Controller, and then change the setting to On.
Connect the network cable to the integrated connector on the back panel of the computer.
Drives
Your computer supports a combination of these devices:
Up to three hard drives
One floppy drive
Up to two CD or DVD drives
Media Card Reader (optional)
1
media card reader (optional)
2
CD/DVD drive(s)
3
hard drive(s)
General Installation Guidelines
Connect serial ATA hard drives to the SATA0 - SATA3 connectors on the system board. Connect CD/DVD drives to the IDE connector.
When you connect two IDE devices to a single IDE interface cable and configure them for the cable select setting, the device attached to the last connector on the interface cable is the primary or the boot device (drive 0), and the device attached to the middle connector on the interface cable is the secondary device (drive 1). See the drive documentation in your upgrade kit for information on configuring devices for the cable select setting.
Connecting Drive Cables
When you install a drive, you connect two cables—a DC power cable and a data cable—to the back of the drive and to the system board. Some drives may also have an audio connector; one end of the audio cable attaches to the drive connector and the other end attaches to the system board.
Drive Interface Connectors
Most interface connectors are keyed for correct insertion; that is, a notch or a missing pin on one connector matches a tab or a filled-in hole on the other connector.
When you connect an IDE cable, ensure that you align the colored stripe with the pin 1 connector. When you disconnect an IDE cable, grasp the colored pull tab and pull until the connector detaches.
When connecting and disconnecting a serial ATA cable, hold the cable by the connector at each end.
NOTE: The system board serial ATA connector may have an attached cover or shroud.
Power Cable Connector
1
power cable
2
power input connector
Hard Drive
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
NOTICE: To avoid damage to the drive, do not set it on a hard surface. Instead, set the drive on a surface, such as a foam pad, that will sufficiently cushion it.
Removing a Hard Drive
NOTE: If you are replacing a hard drive that contains data you want to keep, back up your files before you begin this procedure.
Press in on the top shroud tabs and tilt the shroud back.
Lift the shroud away from the hard drive.
Disconnect the power and hard-drive cables from the drive and from the system board.
1
power cable
2
hard-drive cable
3
tab (2)
4
hard drive
5
system board connector
Press in on the tabs on each side of the drive and slide the drive up and out.
Installing a Hard Drive
Unpack the replacement hard drive, and prepare it for installation.
Check the documentation for the drive to verify that it is configured for your computer.
If your replacement hard drive does not have the bracket rails attached, remove the rails from
the old drive by removing the two screws that secure each rail to the drive. Attach the bracket
rails to the new drive by aligning the screw holes on the drive with the screw holes on the
bracket rails and then inserting and tightening all four screws (two screws on each rail).
1
drive
2
bracket rails (2)
3
screws (4)
Install the hard drive into the computer by gently sliding the drive into place until the tabs
securely click into position.
NOTE: If you are installing a hard drive in the lower bay, place the drive in the bay so that the power connector is on the left-hand side (opposite of the top hard drive).
1
power cable
2
hard-drive cable
3
tab (2)
4
hard drive
5
system board connector
Connect a power cable to the drive.
Connect the hard-drive cable to the drive and to the system board.
Check all connectors to be certain that they are properly cabled and firmly seated.
NOTICE: When replacing the hard-drive shroud, ensure that all the cables are properly routed.
Insert the bottom tabs of the shroud in to the holes on the drive cage and rotate the shroud
up.
Press in on the top tabs and lock them in to place.
Gently press on the shroud to ensure that it is secure.
Exit the system setup program, and restart the computer.
Partition and logically format your drive before you proceed to the next step.
See the documentation for your operating system for instructions.
Test the hard drive by running the Dell Diagnostics.
If the drive you just installed is the primary drive, install your operating system on the hard
drive.
Adding a Second Hard Drive
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before opening the cover.
NOTICE: To avoid damage to the drive, do not set it on a hard surface. Instead, set the drive on a surface, such as a foam pad, that will sufficiently cushion it.
Check the documentation for the drive to verify that it is configured for your computer.
If you are replacing a drive and the new drive does not have the bracket rails attached, remove
the rails from the old drive by removing the two screws that secure each rail to the drive.
Attach the bracket to the new drive by aligning the screw holes on the drive with the screw
holes on the bracket rails and then inserting and tightening all four screws (two screws on
each rail).
1
drive
2
bracket rails (2)
3
screws (4)
Gently slide the drive into place until the tabs securely click into position.
1
data cable
2
power cable
3
tabs (2)
4
floppy drive
Attach the power and data cables to the floppy drive.
Connect the other end of the data cable to the connector labeled "DSKT" on the system
board.
Check all cable connections, and fold cables out of the way to provide airflow for the fan and
cooling vents.
Verify that your computer works correctly by running the Dell Diagnostics.
Media Card Reader (Optional)
Removing a Media Card Reader
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide.
NOTICE: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface on the computer chassis.
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide.
NOTICE: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface on the computer chassis.
Lay the computer on its side so that the system board is on the bottom of the inside of the
computer.
Remove the media card reader and bracket from its packaging.
Attach the adapter rails to the adapter by aligning the screw holes on the adapter with the
screw holes on the rails and then inserting and tightening all four screws (two on each rail).
1
adapter rails (2)
2
screws (4)
Slide the adapter into the 5.25-inch drive bay until the tabs on the rails securely click into
position.
1
internal USB cable
2
tabs (2)
3
media card reader*
4
FLEX connector
Slide the media card reader into the adapter until the tabs on the rails securely click into
position.
Connect the internal USB cable to the media card reader
Route the USB cable through the cable routing clip.
Connect the internal USB cable to the internal FLEX connector on the system board.
Disconnect the power and data cables from the back of the drive.
1
power cable
2
tabs (2)
3
data cable
4
CD/DVD drive
Press inward on the two tabs on the sides of the drive, and then slide the drive upward and
remove it from the drive bay.
Installing a CD/DVD Drive
If you are installing a new drive, unpack the drive and prepare it for installation.
Check the documentation that accompanied the drive to verify that the drive is configured for your computer. If you are installing an IDE drive, configure the drive for the cable select setting.
Connect the new drive to the set of rails that are attached to the inside of the cover. If a set of
rails is not attached inside the computer cover, contact Dell.
If you are installing a replacement drive and the new drive does not have the bracket rails
attached, remove the rails from the old drive by removing the two screws that secure each rail
to the drive. Attach the bracket to the new drive by aligning the screw holes on the drive with
the screw holes on the bracket rails and then inserting and tightening all four screws (two
screws on each rail).
1
drive
2
bracket rails (2)
3
screws (4)
Gently slide the drive into place until the tabs securely click into position.
Connect the power and data cables to the drive.
1
power cable
2
tabs (2)
3
data cable
4
CD/DVD drive
Check all cable connections, and fold cables out of the way to provide airflow for the fan and
cooling vents.
Verify that your computer works correctly by running the Dell Diagnostics.
Processor Airflow Shroud
Removing the Processor Airflow Shroud
CAUTION: Before you perform this procedure, follow the safety instructions in the Product Information Guide.
CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface on the computer chassis.
NOTICE: To avoid damaging the fan power cables, do not slide the shroud too quickly.
Disconnect the two cooling fan power cables from the FANREAR and FANCPU connectors
on the system board (see "System Board Components").
Disconnect the power cable from the POWER12V connector on the system board (see
"System Board Components").
Remove the airflow shroud.
1
anchor tabs (3)
2
shroud release levers (2)
CAUTION: The heat sink can get very hot during normal operation. Be sure that the heat sink has had sufficient time to cool before you touch it.
Remove the heat sink:
Remove the retention module clips. Press the tabs toward the center of the clip and lift.
On the retention base locate the tab opposite the power supply. Press on the retention
base tab away from the heat sink until the heat sink pops up slightly.
Press the second retention tab away from the heat sink while lifting the heat sink up and
out of the retention base.
NOTICE: Lay the heat sink down on its side to avoid damaging the thermal interface on the bottom.
1
heat sink
2
retention tab
3
retention base
NOTICE: If you are installing a processor upgrade kit from Dell, discard the original heat sink. If you are not installing a processor upgrade kit from Dell, reuse the original heat sink and blower when you install your new processor.
Push down and out on the socket release lever.
Open the processor cover.
1
processor cover
2
processor
3
socket
4
release lever
Remove the processor from the socket.
Leave the release lever extended in the release position so that the socket is ready for the new processor.
Installing the Processor
NOTICE: Ground yourself by touching an unpainted metal surface on the back of the computer.
Unpack the new processor.
NOTICE: You must position the processor correctly in the socket to avoid permanent damage to the processor and the computer when you turn on the computer.
If the release lever on the socket is not fully extended, move it to that position.
Align the pin-1 corner of the processor and socket.
1
processor pin-1 indicator
2
release lever
3
processor
4
processor socket
5
socket pin-1 indicator
NOTICE: Socket pins are delicate. To avoid damage, ensure that the processor is aligned properly with the socket, and do not use excessive force when you install the processor. Be careful not to touch or bend the pins on the system board.
Set the processor lightly in the socket and ensure that the processor is level in the socket.
When the processor is positioned correctly, press it with minimal pressure to seat it.
When the processor is fully seated in the socket, close the processor cover.
Pivot the socket release lever back toward the socket and snap it into place to secure the
processor.
NOTICE: If you are not installing a processor upgrade kit from Dell, reuse the original heat sink assembly when you replace the processor.
If you installed a processor replacement kit from Dell, return the original heat sink assembly and processor to Dell in the same package in which your replacement kit was sent.
Install the heat sink:
Slide one end of the heat sink under the retention tab.
Pull out the other retention tab and lower the heat sink until it fits securely in the base.
NOTICE: Ensure that the heat sink is correctly seated and secure.
Reinstall the retention module clips.
Lower the airflow shroud over the heat sink.
Reconnect the two cooling fan power cables to the CPU FAN1 and CPU FAN2 connectors on
the system board (see "System Board Components").
Reconnect the power cable to the POWER12V connector on the system board (see "System
Board Components").
Close the computer cover.
NOTICE: To connect a network cable, first plug the cable into the network port or device and then plug it into the computer.
Connect your computer and devices to electrical outlets, and turn them on.
System Board
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the System Information Guide.
NOTICE: The system board and metal tray are connected and are removed as one piece.
Remove any components that restrict access to the system board.
Disconnect all cables from the system board.
Before you remove the existing system board assembly, visually compare the replacement
system board to the existing system board to make sure that you have the correct part.
Remove the system board screw.
1
screw
2
tab
Pull up on the two tabs, slide the system board assembly toward the front of the computer,
and then lift the assembly up and away.
Place the system board assembly that you just removed next to the replacement system board.
Replacing the System Board
Transfer components from the existing system board to the replacement system board:
Remove the memory modules and install them on the replacement board.
CAUTION: The processor package and heat-sink assembly can get hot. To avoid burns, ensure that the package and assembly have had sufficient time to cool before you touch them.
Remove the heat-sink assembly and processor from the existing system board and
transfer them to the replacement system board.
NOTE: Jumper settings on replacement system boards are preset by the factory.
NOTE: Some components and connectors on the replacement system board may be in different locations than the corresponding connectors on the existing system board.
Orient the replacement board by aligning the notches on the bottom of the board with the
tabs on the computer.
Slide the system board assembly toward the back of the computer until the assembly clicks
into position.
Replace any components and cables that you removed from the system board.
Reconnect all cables to their connectors at the back of the computer.
Close the computer cover.
NOTICE: To connect a network cable, first plug the cable into the network port or device and then plug it into your computer.
Connect your computer and devices to electrical outlets, and turn them on.
Power Supply
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface on the computer chassis.
Removing the Power Supply
NOTICE: Before disconnecting a device from the computer, wait 10 to 20 seconds after disconnecting the computer from its electrical outlet. Before removing a component from the system board, verify that the auxiliary power LED on the system board has turned off. To locate this light, see "System Board Components."
Note the location and ID of each power connector before disconnecting the power supply
cables and the card fan cable.
NOTICE: To avoid damaging the cables when you reinstall the power supply, replace the cables as shown below.
Front Panel
CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface on the computer chassis.
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
Disconnect and remove all disk drives (for more information, see "Drives").
Release the front panel by pressing each of the seven front-panel release tabs.
Close the computer cover halfway and pull the front panel away from the computer.
Front LED Board
CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface on the computer chassis.
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
Gently move the board upward, tilt the top of the board away from the case to release it from
the three front LED board guides, and then draw the board away from the case.
1
LED cable
2
front LED board guides
3
light pipe
4
screw
5
front LED board guide
To replace the front LED board, perform the removal procedure in reverse.
Drive Door
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
Removing the Drive Door
Open the drive door.
Unsnap the top bracket hinge and pull the top of the drive door outward, away from the
computer.
1
top bracket hinge
2
bottom bracket hinge
Lift the bottom bracket hinge away from the computer.
Replacing the Drive Door
To prevent damage to your computer, the drive door is designed to "break away" from the computer if it is opened too far. If the drive door detaches from the computer without disassembling, perform the removal procedure in reverse.
If the drive door is open and it is opened too far, instead of breaking away from the computer in one piece, the drive door may disassemble into several smaller pieces. If the drive door disassembles:
If necessary, reattach the door hinges to the door bracket. Ensure that the hinge tabs are away
from the door bracket.
1
door hinges (2)
2
hinge tab
3
door bracket
Attach the door bracket/door hinge assembly to the door, starting with the lower part of each
door hinge.
1
door
2
door bracket/door hinge assembly
3
lower part of the door hinge
Attach the drive door to the computer, starting with the bottom bracket hinge.
Battery
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide.
NOTICE: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface on the computer chassis.
Replacing the Battery
A coin-cell battery maintains computer configuration, date, and time information. The battery can last several years. If you have to repeatedly reset time and date information after turning on the computer, replace the battery.
CAUTION: A new battery can explode if it is incorrectly installed. Replace the battery only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions.
To replace the battery:
Record all the information on the screens in the system setup program so that you can restore
the correct settings in step 8.
NOTICE: If you pry the battery out of its socket with a blunt object, be careful not to touch the system board with the object. Ensure that the object is inserted between the battery and the socket before you attempt to pry out the battery. Otherwise, you may damage the system board by prying off the socket or by breaking circuit traces on the system board.
Remove the battery by prying it out of its socket with your fingers.
Insert the new battery (CR2032) into the socket with the side labeled "+" against the metal
clip, and press the battery into place.
Close the computer cover.
NOTICE: To connect a network cable, first plug the cable into the network port or device and then plug it into your computer.
Connect your computer and devices to electrical outlets, and turn them on.
