Press this button to eject your CD from the CD drive.
2
hard-drive activity light
The hard drive light is on when the computer reads data from or writes data to the hard drive. The light might also be on when a device such as your CD player is operating.
3
front panel door
Open the door to use the front panel connectors.
4
USB 2.0 connectors (2)
Use the front USB connectors for devices that you connect occasionally, such as joysticks or cameras, or for bootable USB devices (see "Booting to a USB Device" for more information).
It is recommended that you use the back USB connectors for devices that typically remain connected, such as printers and keyboards.
5
headphone connector
Use the headphone connector to attach headphones and most kinds of speakers.
6
power button
Press to turn on the computer.
NOTICE: To avoid losing data, do not turn off the computer by pressing the
power button for 6 seconds or longer. Instead, perform an operating system
shutdown.
NOTE: If your operating system has ACPI enabled, when you press the power button
the computer will perform an operating system shutdown.
7
power light
The power light illuminates and blinks or remains solid to indicate different states:
No light — The computer is in the off state (S4, S5, or mechanical OFF).
Steady green — The computer is in a normal operating state.
Blinking green — The computer is in a power-saving state (S1 or S3).
To exit from a power-saving state, press the power button or click or move the mouse.
See "Diagnostic Lights" for a description of light codes that can help you troubleshoot problems with your computer.
8
floppy-drive activity light
The floppy drive light is on when the computer reads data from or writes data to the floppy drive. Wait until this light turns off before you remove the floppy disk from the drive.
9
floppy-drive eject button
Press to eject a floppy disk from the floppy drive.
Back View
1
power connector
The connection for the power cable.
2
voltage selection switch (may not be available on all computers)
The slots for PCI cards or a second serial port card.
1
parallel connector
Connect a parallel device, such as a printer, to the parallel connector. If you have a USB printer, plug it into a USB connector.
NOTE: The integrated parallel connector is automatically disabled if the computer
detects an installed card containing a parallel connector configured to the same
address. For more information, see "System Setup Options."
2
keyboard connector
If you have a standard keyboard, plug it into the purple keyboard connector. If you have a USB keyboard, plug it into a USB connector.
3
mouse connector
Plug a standard mouse into the green mouse connector. Turn off the computer and any attached devices before you connect a mouse to the computer. If you have a USB mouse, plug it into a USB connector.
If your computer is running Windows 2000 or Windows XP, Dell installed the necessary mouse drivers on your hard drive.
4
link integrity light
Green — A good connection exists between a 10-Mbps network and the computer.
Orange — A good connection exists between a 100-Mbps network and the computer.
Off — The computer is not detecting a physical connection to the network.
5
network adapter
Attach the UTP cable to an RJ45 jack wall plate or to an RJ45 port on a UTP concentrator or hub and press the other end of the UTP cable into the network adapter connector until the cable snaps securely into place.
Dell recommends the use of Category 5 wiring and connectors for our customers' networks.
6
network activity light
The yellow light flashes when the computer is transmitting or receiving network data. A high volume of network traffic may make this light appear to be in a steady "on" state.
7
line-in connector
Use the blue line-in connector (available on computers with integrated sound) to attach a record/playback device such as a cassette player, CD player, or VCR.
On computers with a sound card, the line-in connector is on the card.
8
line-out connector
Use the green line-out connector (available on computers with integrated sound) to attach headphones and most speakers with integrated amplifiers.
On computers with a sound card, the line-in connector is on the card.
9
microphone connector
Use the pink microphone connector (available on computers with integrated sound) to attach a personal computer microphone for voice or musical input into a sound or telephony program.
On computers with a sound card, the microphone connector is on the card.
10
USB connectors
Connect USB devices such as a mouse, keyboard, printer, joystick, and computer speakers into any of the USB connectors.
11
diagnostic lights
Use the lights to help you troubleshoot a computer problem based on the diagnostic code. For more information, see "Diagnostic Lights."
12
video connector
Plug the cable from your VGA-compatible monitor into the blue connector.
13
serial connector
Connect a serial device, such as a handheld device, to the serial port. If you have a second serial connector card installed, you can connect a second device to that connector.
