|
Small Form-Factor Desktop, Small Desktop, and Small Mini-Tower Chassis - Removing
and Replacing Parts: Dell OptiPlex GX150 Service Manual
Back to Contents Page
Small Form-Factor Desktop, Small Desktop, and Small Mini-Tower
Systems — Removing and Replacing Parts: Dell™ OptiPlex™ GX150 Service
Manual
This section provides procedures for removing and replacing the
components, assemblies, and subassemblies in the Dell OptiPlex small form-factor desktop,
small desktop, and small mini-tower chassis GX150 systems. Unless otherwise noted, each
procedure assumes that the following conditions exist:
The GX150 chassis is primarily a tool-less one, but certain
procedures (such as removing drive bracket rails and removing the control panel) require
the use of one or more of the following tools:
- Small flat-blade screwdriver
- #1 and #2 Phillips-head screwdrivers
- An 8-inch, #2 Phillips-head screwdriver
Also, Dell recommends that you use a wrist grounding strap as
explained in "Precautionary Measures."
NOTICE: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell is not covered by your warranty.
 |
CAUTION: Follow the "Safety Instructions" in the
Setup and Quick Reference Guide to help protect your computer from damage and to ensure your own personal safety. |
Before you perform any procedure in this section, read the following
caution for your personal safety and to prevent damage to the system from electrostatic
discharge (ESD).
|
CAUTION: FOR YOUR PERSONAL SAFETY AND PROTECTION OF THE
EQUIPMENT
Before you start to work on the system, perform the following steps in the sequence
listed:
- Perform an orderly
computer shutdown using the operating system menu.
- Turn off the computer and all attached devices.
- Disconnect the computer and devices from their AC power sources.
Also, disconnect any telephone or telecommunication lines from the computer. Doing so
reduces the potential for personal injury or shock.
- If you are disconnecting a device from the computer or are removing a
component from the system board, wait 15 to 30 seconds after disconnecting the computer
from AC power before disconnecting the device or removing the component to avoid possible
damage to the system board.
- Verify that the auxiliary power indicator on the system board is not
on. If it is on, you may need to wait 15 to 30 seconds for it to go out (see "System Board Components" for the location of this indicator).
- Wear a wrist grounding strap, and clip it to an unpainted metal
surface, such as the padlock ring on the back of the chassis. If a wrist grounding strap
is not available, touch an unpainted metal surface on the back of the computer or on the
computer chassis, such as the power supply, to discharge static charge from your body
before touching anything inside the computer. While you work, periodically touch an
unpainted metal surface on the computer chassis to dissipate static electricity that might
harm internal components.
In addition, take note of the following safety guideline when
appropriate:
- Handle components and cards with care. Do not touch the components or
contacts on a card. Hold a card by it edges or by its metal mounting bracket. Hold a
component such as a microprocessor by its edges, not by its pins.
|
 |
NOTE: On the small form-factor and small desktop
systems, remove the stand before you open the computer cover. On the small mini-tower
system, place the system on its side before you open the cover. |
To open the computer cover, perform the following steps:
- Turn off your computer and peripherals, and observe the caution for
your personal safety and protection of your equipment described in "Precautionary Measures."
- If you have installed a padlock through the padlock ring on the back
panel, remove the padlock.
- Open the computer cover as follows:
NOTICE: Do not open the cover if the system is on the edge of a desk
or table. Doing so may cause the system to tip over and fall. Make sure that the system is
situated so that there is at least 12 inches of desk- or table-top for the cover to rest
on.
- Press the two release buttons until the cover is free to swing up.
- Raise the back of the cover, and pivot it toward the front of the
system.
Opening the Small Form-Factor
Desktop Computer Cover
 |
| 1 |
Security cable slot |
| 2 |
Padlock ring |
| 3 |
Release buttons (one on each side) |
|
 |
| 1 |
Release buttons (one on each side) |
| 2 |
Padlock ring |
|
Opening the Small Desktop Computer
Cover
 |
| 1 |
Release buttons (one on each side) |
| 2 |
Padlock ring |
|
Opening the Small Mini-Tower
Computer Cover
 |
| 1 |
Release buttons (one on each side) |
| 2 |
Padlock ring |
|
NOTICE: On the small mini-tower system, to prevent damage to the
system board, open the cover until it catches at a 45-degree angle. Then remove the
optical-drive data cable and/or the hard drive data cable from the system board and open
the cover to a 90-degree angle.
Opening the Small Mini-Tower System to a 45-Degree Angle
Closing the Computer Cover
To close the computer cover, perform the following steps:
- Check all cable connections, especially those that might have come
loose during your work. Fold cables out of the way so that they do not catch on the
computer cover. Make sure cables are not routed over the drive cage—they will prevent
the cover from closing properly.
- Check to see that no tools or extra parts (including screws) are left
inside the computer's chassis.
- In the small mini-tower system, close the cover to a 45-degree angle
and connect the optical-drive data cable and hard drive data cable to the system
board.
- Close the computer cover by pivoting the cover down toward the back
of the chassis and into position. Make sure that the release buttons click into place.
- If you are using a padlock to secure your system, reinstall the
padlock.
| |
NOTE: After you open and close the
cover, the chassis intrusion detector causes the following message to be displayed at the
next system start-up:
ALERT! Cover was previously removed.
See "Resetting the Chassis Intrusion Detector" for
instructions. |
| |
NOTE: User service access points are
color-coded green. |
Inside the Small
Form-Factor Desktop System
 |
| 1 |
Hard drive |
| 2 |
Diskette drive (supports
slimline devices) |
| 3 |
Optical drive (supports
slimline devices) |
| 4 |
Internal
speaker |
| 5 |
Chassis
intrusion switch |
| 6 |
Power supply
release button |
| 7 |
Power supply |
| 8 |
AC power
connector |
| 9 |
I/O ports
and connectors |
| 10 |
Padlock ring |
| 11 |
Microprocessor
and heat sink |
| 12 |
System
board |
|
Inside the Small
Desktop System
 |
| 1 |
Diskette drive |
| 2 |
Hard drive |
| 3 |
Internal speaker |
| 4 |
Chassis intrusion switch |
| 5 |
Expansion-card cage |
| 6 |
Power supply |
| 7 |
Expansion-card slots |
| 8 |
AC power connector |
| 9 |
Padlock ring |
| 10 |
I/O ports and connectors |
| 11 |
Microprocessor and heat sink |
| 12 |
System board |
| 13 |
Optical drive |
|
Inside the Small
Mini-Tower System
NOTICE: This view shows the optical-drive data cable
removed.
 |
| 1 |
Optical drive |
| 2 |
Diskette drive |
| 3 |
Hard drive |
| 4 |
Internal speaker |
| 5 |
Chassis intrusion switch |
| 6 |
System board |
| 7 |
Expansion-card slots |
| 8 |
I/O ports and connectors |
| 9 |
AC power connector |
| 10 |
Power supply |
| 11 |
Padlock ring |
| 12 |
Microprocessor and heat-sink
shroud |
|
Cabling in the Small Form-Factor Desktop System
With Strip Cables
 |
| 1 |
Optical-drive data cable |
| 2 |
Diskette-drive data cable |
| 3 |
Control-panel
cable |
| 4 |
Optical-drive power cable |
| 5 |
IDE drive
power cable (hard drive) |
| 6 |
IDE data
cable (hard drive) |
| 7 |
Input/output cable |
| 8 |
Input/output audio cable |
| 9 |
Optical-drive audio cable |
|
Cabling in the Small Form-Factor Desktop System
With Combination Data Cables
 |
| 1 |
Control
panel cable |
| 2 |
EIDE
interface cable (hard drive) |
| 3 |
Optical-drive power cable |
| 4 |
Diskette-drive data cable |
| 5 |
Optical-drive data cable |
| 6 |
EIDE power
cable (hard drive) |
| 7 |
Front
input/output cable |
| 8 |
Front
input/output audio cable |
| 9 |
Optical-drive audio cable |
|
Cabling in the Small Desktop System Without a Sound Card
Installed
 |
| 1 |
Optical-drive audio cable |
| 2 |
Optical-drive data cable |
| 3 |
Diskette-drive data cable |
| 4 |
Control panel cable |
| 5 |
Front input/output cable |
| 6 |
Front input/output audio cable |
| 7 |
EIDE interface cable (hard
drive) |
|
Cabling in the Small Desktop System With a Sound Card Installed
 |
| 1 |
Optical-drive audio cable |
| 2 |
Optical-drive data cable |
| 3 |
Diskette-drive data cable |
| 4 |
Control panel cable |
| 5 |
Front input/output cable |
| 6 |
Front input/output audio cable |
| 7 |
EIDE interface cable (hard
drive) |
|
Cabling in the Small Mini-Tower System
 |
| 1 |
Optical-drive power cable |
| 2 |
Optical-drive audio cable |
| 3 |
Optical-drive data cable |
| 4 |
Diskette-drive data cable |
| 5 |
Diskette-drive power cable |
| 6 |
Hard-drive power cable |
| 7 |
Hard-drive data cable |
| 8 |
Front input/output cable |
| 9 |
Front input/output audio cable |
|
The following table provides a color code key for the cables inside
the system.
| Hard drive |
Blue |
| Diskette drive |
Black |
| Optical drive |
Orange |
| USB |
Gray |
| ATA, IDE, or EIDE drive |
Green |
| Control panel |
Yellow |
| CD audio |
Blue |
| System audio |
Black |
- Face the front of the computer and
grasp the right and left sides of the plastic computer cover. Dislodge the plastic cover
from the metal chassis and pull the plastic out and away.
- Remove the piece covering the control panel.
- Remove the screw that holds the control panel to the chassis.
- Remove the plastic part of the computer cover (see step 1 in the previous procedure).
- From the inside of the front panel, push in on the two tabs on either
side of the badge to release the badge.
- Press on the badge until it is freed.
Replacing the Control Panel and
Badge—Small Form-Factor Desktop System
Replace the control panel and badge by following, in reverse order,
the procedures in "Removing the Control Panel—Small
Form-Factor Desktop System" and "Removing the
Badge—Small Form-Factor Desktop System."
Removing the Control Panel—Small Desktop
System
- Remove the front I/O panel.
- Using an 8-inch, #2 Phillips-head screwdriver,
remove the screw holding the control panel to the chassis and pull the panel up and away
from the chassis.
Removing the Badge—Small Desktop
System
- Open the front USB door.
- From the inside of the door, push in on the two tabs on either side
of the badge to release the badge.
- Press on the badge until it is freed.
Replacing the Control Panel—Small
Desktop System
- Replace the control panel and secure it to the chassis by replacing
the screw you removed in step 2.
- Replace the front I/O panel.
Replacing the Badge—Small Desktop System
Slightly tilt the replacement badge so that the lever fits through
the slot on the front panel. Straighten the button and press it into place.
Removing the Control Panel and
Badge—Small Mini-Tower System
- Lay the computer on its right side and open
the cover.
- Remove the top and bottom panels of the computer by releasing the
eight tabs on each panel.
- Remove the front panel:
- Release the three tabs located on the front panel; one tab is located
by the CD drive and two tabs are located by the I/O panel.
- Close the cover and remove the front panel.
NOTICE: This view of the small mini-tower system shows the
optical-drive data cable removed.
 |
| 1 |
Top panel |
| 2 |
Bottom panel |
| 3 |
Front-panel tabs (3) |
| 4 |
Top-panel tabs (8) |
|
- Remove the screw holding the control panel to the chassis, and pull
the panel up and away from the chassis.
- Remove the badge by pressing in on the small lever that holds the
badge to the front panel. Press on the badge until it is freed.
Replacing the Control Panel and
Badge—Small Mini-Tower System
To replace the control panel and badge, follow the "Removing the Control Panel and Badge—Small Mini-Tower
System" procedures in reverse, ensuring that the tabs on the top, bottom, and
front panels are secure.
Removing Front-Panel Inserts—Small Desktop System
- Facing the front of the computer, use your fingers to remove the
front-panel cover.
 |
| 1 |
Optical drive front-panel cover |
| 2 |
Diskette drive front-panel cover |
|
- Press on the insert until it pops free of the front-panel cover.
Removing Front-Panel Inserts—Small
Mini-Tower System
- Open the computer cover to a 45-degree angle and disconnect the
optical-drive data cable.
- Open the cover to a 90-degree angle and release the insert tabs from
inside the chassis.
- Press on the insert until it pops free of the front-panel cover.
Replacing Front-Panel Inserts
To replace a front-panel insert, follow the "Removing Front-Panel Inserts" procedures in reverse.
Removing the Front I/O
Panel—Small Form-Factor Desktop System
- To access the screw that holds the front I/O panel to the chassis, remove the hard drive.
- Disconnect the control panel cable from
the control panel connector on the I/O panel. Disconnect the front I/O cable from the
connector on the system board (see "System Board Components"
for the location of the front-panel connector and front I/O cable).
- Remove all cables that are connected to the front I/O panel.
- From inside the chassis cover, remove the mounting screw that secures
the front I/O panel to the chassis.
- Remove the front I/O panel from the chassis.
Removing the Front I/O
Panel—Small Desktop System
- Remove the hard-drive shroud.
- Disconnect the hard-drive data cable.
- Disconnect the control panel cable from
the control panel connector. Disconnect the I/O cable from the connector on the system
board (see "System Board Components" for the location of
the front-panel connector and I/O cable).
Note the routing of the control panel cable as you remove it from the chassis so that you
can replace it correctly.
- Remove all cables that are connected to the front I/O panel.
- From inside the chassis cover, remove the mounting screw that secures
the front I/O panel to the chassis.
- Remove the front I/O panel from the chassis.
Removing the Front I/O
Panel—Small Mini-Tower System
- Disconnect the control panel cable from
the control panel connector. Disconnect the I/O cable from the connector on the system
board (see "System Board Components" for the location of
the front-panel connector and I/O panel).
Note the routing of the control panel cable as you remove it from the chassis so that you
can replace it correctly.
- Remove all cables that are connected to the front I/O panel.
- From inside the chassis cover, remove the mounting screw that secures
the front I/O panel to the chassis.
- Remove the front I/O panel from the chassis.
Replacing the Front I/O
Panel—Small Form-Factor Desktop, Small Desktop, and Small Mini-Tower Systems
To replace the front I/O panel, follow the "Removing
the Front I/O Panel" procedures in reverse.
Removing the Chassis Intrusion Switch—Small Form-Factor
Desktop System
Removing the Chassis Intrusion Switch—Small Desktop System
Removing the Chassis Intrusion
Switch—Small Mini-Tower System
- Disconnect the chassis intrusion switch cable connector from the
control panel on the front of the chassis.
Note the routing of the chassis intrusion cable as you remove it from the chassis. Chassis
hooks may hold the cable in place inside the chassis.
- Slide the chassis intrusion switch out of its slot and remove the
switch and its attached cable from the chassis.
Replacing the Chassis Intrusion Switch
To replace the chassis intrusion switch, follow the "Removing the Chassis Intrusion Switch" procedures in
reverse order.
- Enter system setup by pressing <F2> during the system's POST.
|
NOTE: For instructions on using system setup, see
the online System User's Guide. |
- Under the System Security tab, reset the Chassis Intrusion
option by pressing the left- or right-arrow key to select Reset. Change the setting
to Enabled, Enabled-Silent, or Disabled.
|
NOTES: The default is Enabled-Silent.
If a setup password has been assigned by someone else, contact the network
administrator for information on resetting the chassis intrusion detector. |
- Press <Alt><B> to restart the system and implement your
changes.
|
CAUTION: To avoid the possibility of electric
shock, turn off the computer and any peripherals, disconnect them from electrical outlets,
and then wait at least 5 seconds before you open the computer cover. Also, before you
install a drive, read the steps in "Precautionary Measures." |
Small Form-Factor Desktop System
Small Desktop System
Small Mini-Tower System
Removing the Diskette
Drive—Small Form-Factor Desktop System
Select the appropriate instructions for the system:
| Diskette Drive With the Strip Cable |
 |
| Diskette Drive With the Combination Data Cable |
 |
Removing
the Diskette Drive With the Strip Cable
- Disconnect the diskette-drive cable from the system board.
- Remove the power cable from the interposer board.
- Remove or raise the drive by pressing the green tabs on either side
of the drive and lifting the drive up.
- Remove the diskette-drive cable from the
diskette drive.
- Remove the interposer board from the diskette drive by pressing
the tab and rotating the interposer board.
Removing the Interposer Board—Small Form-Factor Computer
|
| 1 |
Diskette-drive cable |
| 2 |
Tab |
| 3 |
Interposer board |
| 4 |
System board
diskette-drive connector (DSKT) |
|
- To release the diskette-drive cable from the connector, slide the
lever until it is fully extended, and then lift the cable away.
Removing the Diskette-Drive Cable
|
| 1 |
Diskette-drive cable |
| 2 |
Lever |
|
- Remove the diskette drive from its sled by pulling the sled tab out while
pushing the drive up, and then sliding the drive out of the sled.
Removing the Diskette Drive—Small Form-Factor Computer
Removing
the Diskette Drive With the Combination Data Cable
- Open
the computer cover.
- Disconnect the combination data cable from the interface (IDE2) and diskette-drive data
connectors on the system board.
Removing the Cables on the Diskette Drive—Small-Form
Factor System
 |
| 1 |
Power cable |
| 2 |
Audio cable |
| 3 |
Optical interposer board |
| 4 |
ZIF lever |
| 5 |
Combination data cable |
| 6 |
System board diskette-drive connector |
| 7 |
System board interface connector (IDE2) |
|
- Disconnect the power cable and audio cable from the interposer board
and then remove the interposer board from the optical drive.
- Press inward on the two tabs on the sides of the diskette drive to
disengage the drive from the chassis and then slide the drive upward and remove it from the
chassis.
- Disconnect the diskette-drive data cable
from the back of the drive by first releasing the ZIF lever.
Once this lever is released, the cable is easily removed from the connector.
Removing the Diskette-Drive Data Cable
 |
| 1 |
Diskette-drive data cable |
| 2 |
ZIF lever |
| 3 |
System board diskette-drive connector |
|
- Remove the diskette drive from the sled by pulling the sled tab out
while pushing the drive up, and then sliding the drive out of the sled.
Removing and Replacing the Sled
Replacing the
Diskette Drive�Small Form-Factor Desktop System
Select the appropriate instructions for the system:
| Diskette Drive With the Strip Cable |
|
| Diskette Drive With the Combination Data Cable |
|
Replacing
the Diskette Drive With the Strip Cable
- Snap the replacement drive into the sled and ensure that it is secure in
the sled.
- Connect the interposer board to the diskette drive.
- Slide the diskette-drive cable into the connector.
- Close the lever so that the cable is secure in the connector.
- Line up the hole on the bottom of the interposer board with the
notch on the connector, and snap the interposer board onto the
drive.
- Gently slide the drive into the computer until the tabs securely click
into position.
|
| 1 |
Connector notch |
| 2 |
Interposer board alignment hole |
| 3 |
Diskette-drive cable |
| 4 |
Lever |
|
- Attach the power cable to the interposer board on the
diskette drive.
- Connect the strip cable to the DSKT connector on the system board.
- Check all cable connections, and fold cables out of the way to provide
airflow for the fan and cooling vents.
- Close the computer cover, reconnect your computer and devices to
their electrical outlets, and turn them on.
- Enter system setup and update the appropriate Diskette Drive A
option to reflect the size and capacity of your new diskette drive.
- Verify that your computer works correctly by running the
Dell Diagnostics.
- Snap the replacement drive into the sled and ensure that it is secure
in the sled.
- Attach the diskette-drive data cable to the back of the diskette
drive by inserting the cable into the connector and then sliding the ZIF lever to lock the
cable into place.
Attaching the Diskette-Drive Data Cable—Small
Form-Factor System
 |
| 1 |
Diskette-drive data cable |
| 2 |
ZIF lever |
|
- Gently slide the drive into the chassis until the tabs securely click
into position.
Replacing the Diskette Drive—Small
Form-Factor System
 |
| 1 |
Diskette-drive data cable |
|
- Connect the interposer board to the optical drive and connect the
power cable and audio cable.
Attaching Cables—Small Form-Factor System
 |
| 1 |
Power cable |
| 2 |
Audio cable |
| 3 |
Interposer board |
| 4 |
ZIF lever |
| 5 |
Combination data cable |
| 6 |
System board diskette-drive connector |
| 7 |
System board interface connector (IDE2) |
|
- Connect the combination data cable to the diskette and interface
(IDE2) connectors on the system board.
- Close the computer cover.
Removing the Diskette Drive—Small Desktop and Small
Mini-Tower Systems
- Open the computer cover.
- Disconnect the power cable and the diskette-drive data cable from the drive.
- Press inward on the two tabs on the sides of the drive bay to
disengage the bracket from the chassis.
- Slide the bracket upward, and remove it from the chassis.
Removing the Diskette Drive—Small Desktop System
Removing the Diskette Drive—Small Mini-Tower System
- If the replacement drive does not have the bracket rails attached,
remove the rails from the old drive by removing the four screws that secure each rail to
the drive.
- Attach the bracket to the new drive by aligning the screw holes on
the drive with the screw holes on the bracket rails and tightening all four screws.
Removing and Replacing the Drive Bracket Rails—Small
Desktop and Small Mini-Tower Systems
 |
| 1 |
Drive |
| 2 |
Bracket rails (2) |
| 3 |
Screws (4) |
|
- Ensure that bracket rails are attached to the new drive.
- Gently slide the bracket into place until the tabs securely click
into position.
- Attach the diskette-drive data cable to the back of the diskette
drive.
- Connect the power cable to the power input connector on the drive.
- If the drive bay was previously empty, remove
the front-panel insert from the front panel.
Attaching Cables to a Diskette
Drive—Small Desktop System
 |
| 1 |
Power cable |
| 2 |
Diskette-drive data cable |
| 3 |
Diskette-drive system board connector |
|
Attaching Cables to a Diskette
Drive—Small Mini-Tower System
 |
| 1 |
Power cable |
| 2 |
Diskette-drive data cable |
| 3 |
Diskette-drive system board connector |
|
- Close the computer cover.
Small Form-Factor Desktop System
Small Desktop System
Small Mini-Tower System
Removing the Optical Drive—Small Form-Factor Desktop System
Select the appropriate instructions for the system:
| Optical Drive With the Strip Cable |
 |
| Optical Drive With the Combination Data Cable |
|
Removing
the Optical Drive With the Strip Cable
- Remove the interposer board from the CD drive.
Removing the Interposer Board—Small Form-Factor
System
- Press inward on the two tabs on the sides of the drive to disengage the
drive from the computer.
Removing
the Optical Drive With the Combination Data Cable
- Open the computer cover.
- Remove the interposer board from the optical drive.
Removing Cables—Small Form-Factor
Desktop System
 |
| 1 |
Interposer board |
| 2 |
Optical-drive interface connector |
| 3 |
Combination data cable |
| 4 |
System board diskette-drive connector |
| 5 |
System board interface (IDE2) connector |
|
- Press inward on the two tabs on the sides of the drive bay to
disengage the drive from the chassis.
Replacing the Optical Drive�Small
Form-Factor System
Select the appropriate instructions for the system:
| Optical Drive With the Strip Cable |
|
| Optical Drive With the Combination Data Cable |
|
Replacing
the Optical Drive With the Strip Cable
- If you are replacing a drive that does not have the bracket rails
attached, remove the rails from the old drive by removing the two
screws that secure each rail to the drive. Attach the bracket to the new
drive by aligning the screw holes on the drive with the screw holes on
the bracket rails, and then tightening all four screws (two screws for each
rail).
- If you are installing a new drive, connect it to the set of rails that are
attached to the inside of the cover.
If a set of rails is not attached to the inside of the cover, contact Dell.
CD Drive Bracket Rails
|
| 1 |
Drive |
| 2 |
Bracket rails (2) |
| 3 |
Screws (4) |
|
- Gently slide the drive into place until the tabs securely click into
position.
- Connect the interposer board to the CD drive, ensuring that the data,
power, and audio cables are attached to the interposer board.
Connecting the Interposer Board—Small Form-Factor
System
Replacing the Optical Drive
With the Combination Data Cable
- Gently slide the drive into place until the tabs securely click into
position.
- Connect the interposer board to the optical drive.
- Close the computer cover.
Attaching Cables to an
Optical Drive—Small Form-Factor Desktop System
 |
| 1 |
Interposer board |
| 2 |
Optical-drive interface connector |
| 3 |
Combination data cable |
| 4 |
System board diskette-drive connector |
| 5 |
System board interface (IDE2) connector |
|
Removing the Optical Drive—Small Desktop System
Removing the Optical Drive—Small Mini-Tower System
Removing and Replacing the Drive Bracket Rails—Small
Desktop and Small Mini-Tower Systems
|
| 1 |
Drive |
| 2 |
Bracket rails (2) |
| 3 |
Screws (4) |
|
If you are replacing an optical drive and bracket assembly, follow
these instructions. If you are installing a new drive that does not have bracket rails
attached, connect it to the set of rails that is attached to the inside of the cover.
|
NOTE: If there are no screws with the bracket rails
in the small mini-tower system, contact Dell. See the User's Guide for information on
contacting Dell. |
- Open the computer cover.
- Remove the optical-drive data cable from the optical drive.
- Remove the optical-drive power cable and audio cable from the optical
drive.
- Press inward on the two tabs on the sides of the drive bay to
disengage the bracket from the chassis.
- Slide the bracket upward and remove it from the chassis.
- If the replacement drive does not have the bracket rails attached,
remove the rails from the old drive by removing the two screws that secure each rail to
the drive.
- Attach the bracket to the new drive by aligning the screw holes on
the drive with the screw holes on the bracket rails and tightening all four screws.
Replacing the Optical
Drive—Small Desktop and Small Mini-Tower Systems
- Reinstall the optical drive and bracket assembly in the chassis by
gently sliding the drive into place until the tabs securely click into position.
- If you are installing a drive that has its own controller card, install the controller card in an expansion slot.
- Connect the optical-drive power cable and audio cable to the optical
drive.
- Connect the optical-drive data cable to the optical drive.
If your system came with an EIDE CD drive, use the spare connector
on the existing interface cable. Otherwise, use the EIDE interface cable provided in the
drive kit.
Attaching Cables to an
Optical Drive—Small Desktop System
 |
| 1 |
Optical-drive data cable |
| 2 |
Optical-drive interface connector |
| 3 |
Power cable |
| 4 |
Power connector |
| 5 |
Audio connector |
| 6 |
Audio cable |
|
Attaching Cables to an
Optical Drive—Small Mini-Tower System
 |
| 1 |
Power connector |
| 2 |
Optical-drive data cable |
| 3 |
Audio connector |
| 4 |
System board interface connector (IDE2) |
|
|
NOTE: If you install a second optical device, do
not route the cable through the plastic clips on the side of the diskette-drive bay. |
- If the replacement drive does not have the bracket rails attached,
remove the rails from the old drive by removing the two screws that secure each rail to
the drive.
- Close the computer cover.
Small Form-Factor Desktop System
Small Desktop System
Small Mini-Tower Chassis
Removing the Hard-Drive Shroud—Small Desktop System
- Open the computer cover.
- Remove the plastic shroud covering the hard drive by pressing in on
the indented tab at the top of the shroud and lifting the shroud away.
Removing the Hard Drive—Small
Form-Factor Desktop System
Removing the Hard Drive—Small
Desktop System
Removing the Hard Drive—Small
Mini-Tower System
- Disconnect the power and interface cables from the drive.
- For the small form-factor system, press in on the tabs on each side
of the bracket, slide the drive toward the I/O panel, and remove the drive from the
chassis.
For the small desktop and small mini-tower systems, press in on the
tabs on each side of the bracket, and slide it up and out.
- If your replacement hard drive does not have the bracket rails
attached, remove the four screws holding the bracket rails to the hard drive.
NOTICE: To avoid possibly damaging the drive by ESD, ground
yourself by touching an unpainted metal surface on the back of the chassis.
NOTICE: When you unpack the drive, do not set it on a hard surface, which may damage
the drive. Instead, set the drive on a surface, such as a foam pad, that will sufficiently
cushion it.
- If necessary, attach the bracket rails to the new hard drive by
aligning the four screw holes of the drive and bracket and then inserting and tightening
the screws that came with your upgrade kit.
- Reinstall the hard-drive bracket in the chassis by gently sliding the
bracket into place until you hear it securely click.
- On the small desktop system, replace the hard-drive shroud.
- Connect a power cable to the power input connector on the back of the
drive, and connect one of the device connectors on the EIDE cable
to the 40-pin interface connector on the back of the hard drive.
- Check all connectors to be certain that they are properly cabled and
firmly seated.
NOTICE: To avoid possible damage to the system, you must match
the colored stripe on the EIDE interface cable with pin 1 on the drive's interface
connector and with the EIDE interface connector (labeled IDE1) on the system board.
To locate EIDE connector 1 (IDE1) on the system board, see "System
Board Components."
Attaching Hard-Drive
Cables—Small Form-Factor Desktop System
 |
| 1 |
Drive power connector |
| 2 |
Hard-drive power cable |
| 3 |
Drive IDE1 connector |
| 4 |
Hard-drive data cable |
| 5 |
System board IDE1 connector |
|
Attaching Hard-Drive
Cables—Small Desktop System
 |
| 1 |
Hard-drive power cable |
| 2 |
Hard-drive data cable |
| 3 |
IDE1 connector |
|
Attaching Hard-Drive Cables—Small
Mini-Tower System
 |
| 1 |
Hard-drive data cable |
| 2 |
Hard-drive power cable |
| 3 |
IDE1 connector |
|
- Close the computer cover.
- If the drive you just installed is the primary drive, insert a
bootable system diskette disk into the diskette drive.
- Turn on the computer.
- Enter system setup and update the appropriate Primary Drive
option, 0 or 1.
See the User's Guide for complete information on system setup.
- Reset the chassis intrusion detector.
- Restart the system.
- Partition and logically format the system's hard drive before
proceeding to the next step.
For partition and format instructions, refer to the documentation
that came with the operating system.
| |
NOTE: On systems with hard drives
larger than 2 GB, create a primary partition of 2 GB and divide the remaining capacity
into partitions of 2 GB or less. For example, a system with a 2.5-GB hard drive would have
a primary partition of 2 GB (drive C) and a second partition of 500 MB (drive D). Hard
drives must be partitioned this way because MS-DOS�-based operating systems (including
Microsoft� Windows NT�, when using a FAT16 file system) do not support drive partitions
larger than 2 GB. |
- Test the hard drive by running the Dell Diagnostics.
See "Solving Problems" in the User's Guide for complete information.
- If the drive you just installed is the primary drive, install the
operating system on the hard drive.
For instructions, refer to the documentation that came with the operating system.
Removing the Power Supply—Small
Form-Factor Desktop System With a 160-Watt Power Supply
 |
| 1 |
Release button |
| 2 |
AC power connector |
|
Removing the Power Supply—Small
Form-Factor Desktop System With an 85-Watt Power Supply
 |
| 1 |
DC power cables |
| 2 |
Push button |
| 3 |
AC power connector |
|
Removing the Power Supply—Small
Desktop System
 |
| 1 |
DC power cables |
| 2 |
AC power connector |
| 3 |
Push button |
|
Removing the Power Supply—Small
Mini-Tower System
 |
| 1 |
DC power cables |
| 2 |
Push button |
| 3 |
Screws (2) |
| 4 |
AC power connector |
|
- Disconnect the AC power cable from the back of the power supply.
- Disconnect the DC power cables from the system board and the drives.
Note the routing of the DC power cables underneath the tabs in the chassis as you remove
them from the system board and drives. It is important to route these cables properly when
you replace them to prevent them from being pinched or crimped.
- On the small desktop system, remove the
expansion-card cage, and remove the power cables from the side of the hard-drive cage.
To remove the power cables, use the cables as leverage and pull away from the clips while
simultaneously pulling on the metal clips with your finger.
On the small mini-tower chassis, remove the two screws that secure
the power supply to the back of the chassis.
- Press the "PUSH" button located on the floor of the
chassis.
- Slide the power supply toward the front of the system approximately 1
inch.
- Lift the power supply up and out of the chassis.
Replacing the Power Supply
- Slide the power supply into place.
- On the small mini-tower system, replace the two screws that secure
the power supply to the back of the chassis.
- Reconnect the DC power cables.
- Connect the AC power cable to the connector.
- On the small desktop system, reattach the power cables to the side of
the hard-drive cage.
- Run the cables underneath the metal clips.
- Press the clips to close them over the cables.
Removing the Expansion-Card
Cage—Small Desktop System
- Examine any cables connected to
expansion cards through the back-panel openings, and disconnect any cables that will not
extend to where the cage must be placed when it is removed from the chassis.
- Remove any cables connected to the expansion card.
- Gently pull on the handle and lift the expansion-card cage up and
away from the chassis.
Replacing the Expansion-Card Cage
- Align the expansion-card cage slots with the tabs in the chassis
opening for the expansion-card cage. Slide the expansion-card cage into place.
- Make sure that the riser board is fully seated in the RISER connector
on the system board.
- Reconnect any cables you removed in step 1
and 2 of the previous procedure.
 |
| 1 |
PCI expansion-card connector 1 (PCI1) |
| 2 |
PCI expansion-card connector 2 (PCI2) |
|
Removing the PCI Riser Board on the
Small Desktop System
NOTICE: To avoid damage to the expansion cards or the system board by ESD, ground
yourself by touching an unpainted metal surface on the back of the computer.
- Remove the expansion-card cage.
- Remove the expansion cards installed in
the slots.
- Remove the two screws that attach the riser board to the
expansion-card cage.
Replacing the PCI Riser Board on the
Small Desktop System
Follow the "Removing the PCI Riser
Board" procedures in reverse order.
Removing the PCI Riser Board on the Small
Mini-Tower System
NOTICE: To avoid damage to the expansion cards or the system
board by ESD, ground yourself by touching an unpainted metal surface on the back of the
computer.
- Remove all cables from the system board.
- Remove the system board metal tray
assembly.
- Detach the riser board from the system board metal tray assembly.
|
NOTE: The metal tab on the PCI riser board may be
engaged; release the tab before you remove the riser board. You do not need to engage this
tab when you replace the riser board. |
 |
| 1 |
PCI riser board |
| 2 |
System board |
| 3 |
System board tab |
| 4 |
Riser board tab |
|
Replacing the PCI Riser Board on the Small Mini-Tower System
Follow the "Removing the PCI Riser Board"
procedures in reverse order.
The small form-factor desktop system supports one expansion slot for
a low-profile, 32-bit, 33-MHz PCI card. The small desktop system accommodates up to two
32-bit PCI expansion cards. The small mini-tower system supports up to four 32-bit PCI
expansion cards.
| |
NOTE: Before disconnecting a device from the system
or removing a component from the system board, verify that the auxiliary power indicator
LED on the system board is off. For the location of this LED, see "System Board Components." |
32-Bit Low Profile Expansion Card
32-Bit Expansion Card
- If necessary, disconnect any cables connected to the card.
- In the small desktop system, remove the
expansion-card cage.
- Raise the plastic lever that secures the card you want to remove.
- Grasp the card by its top corners, and ease it out of its connector.
- If you are removing the card permanently, install a filler bracket in
the empty card-slot opening.
|
NOTE: Installing filler brackets over empty
card-slot openings is necessary to maintain FCC certification of the system. The brackets
also keep dust and dirt out of your system. |
- Close the computer cover, reconnect
the computer and peripherals to their electrical outlets, and turn them on.
|
NOTE: After you open and close the cover,
the chassis intrusion detector causes the following message to appear on the screen at the
next system start-up: ALERT! Cover was
previously removed. |
- Reset the chassis intrusion detector by changing Chassis
Intrusion to Enabled or Enabled-Silent.
|
NOTE: If a setup password has been
assigned by someone else, contact your network administrator for information on resetting
the chassis intrusion detector.
|
- If you removed a sound card, enter system setup, select Integrated
Devices, and change the setting for Sound to On.
Replacing an Expansion Card—Small Form-Factor System
Replacing an Expansion Card—Small
Desktop System
 |
| 1 |
Card-edge connector |
| 2 |
Expansion card |
| 3 |
Riser board |
| 4 |
PCI expansion-card connector |
| 5 |
Expansion-card cage |
|
Replacing an Expansion Card—Small Mini-Tower Chassis
|
CAUTION: Some network cards automatically start the
system when they are connected. To guard against electrical shock, be sure to unplug the
computer from its electrical outlet before installing any expansion cards. |
- Prepare the expansion card for installation.
See the documentation that came with the expansion card for information on
configuring the card, making internal connections, or otherwise customizing it for your
system.
- Raise the lever that covers the card-slot opening on the back of the
chassis.
- If there is a filler bracket, remove the filler bracket by raising
the hinged lever and sliding the bracket up.
- Place the expansion card on the connector and press down firmly. Make sure
that the card is fully seated in the slot.
If the expansion card is full-length, insert the end of the card into the
expansion-card guide bracket as you lower the card toward its connector on
the system board. Insert the card firmly into the expansion-card connector
on the system board.
Expansion-Card Connection
 |
| 1 |
Bracket within slot |
| 2 |
Bracket caught outside of slot |
| 3 |
Fully seated card |
| 4 |
Not fully seated card |
|
- Before lowering the retention arm, make sure of the following:
- Tops of all expansion cards and filler brackets are flush with the
alignment bar.
- Notch in the top of the card or filler bracket fits around the
alignment guide.
Press the arm into place, securing the expansion card(s) in the computer.
Retention Arm Closure
 |
| 1 |
Filler bracket |
| 2 |
Retention arm |
| 3 |
Alignment bar |
| 4 |
Alignment guide |
|
- Connect any cables that should be attached to the card.
- In the small desktop system, replace the expansion-card cage.
- Close the computer cover, and
reconnect the computer and devices to their electrical outlets and turn them on.
| |
NOTE: After you open and close the
cover, the chassis intrusion detector causes the following message to be displayed at the
next system start-up:
ALERT! Cover was previously removed.
See "Resetting the Chassis Intrusion Detector" for
instructions. |
The subsections that follow contain procedures for removing system
board components.
System Board Components
Front of Computer
Back of Computer |
| 1 |
PC speaker |
| 2 |
DC power connector |
| 3 |
Diskette-drive connector |
| 4 |
Battery |
| 5 |
EIDE2 connector |
| 6 |
Auxiliary power indicator |
| 7 |
Memory module (DIMM) connectors (2) |
| 8 |
Front-panel cable connector |
| 9 |
EIDE1 connector |
| 10 |
PCI 2 riser connector (not populated on
the small form-factor system, used as the riser in the small desktop system, and can be
populated with PCI expansion card in the small mini-tower system) |
| 11 |
PCI 1 connector (not able to be populated
on the small desktop system) |
| 12 |
AGP/GPA connector |
| 13 |
Video connector (upper) and audio
connectors (lower) |
| 14 |
CD audio and telephony connectors |
| 15 |
NIC connector (upper) and USB connectors
(2) (lower) |
| 16 |
Keyboard (lower) and mouse (upper)
connectors |
| 17 |
Diagnostic LEDs |
| 18 |
Voltage regulator module (may not be
removable on some systems) |
| 19 |
Parallel port (upper) and serial port (2)
(lower) connectors |
| 20 |
Microprocessor fan connector |
| 21 |
Microprocessor and heat-sink assembly |
|
The following figure shows the location of the PSWD jumper on the
system board.
System Board Jumper
The following table lists the labels for connectors and sockets on
the system board and gives a brief description of their functions.
System Board Connectors and Sockets
| Connector or Socket |
Description |
| AGP |
Accelerated Graphics Port (AGP) Pro
connector |
| AUDIO |
Line-in, line-out, and microphone jacks |
| AUX_PWR |
Auxiliary power indicator |
| BATTERY |
Battery socket |
| CD-IN |
CD-ROM drive audio cable connector |
| DIAG_LED |
Diagnostic LEDs |
| DIMM_x |
DIMM socket |
| DSKT |
Diskette-drive interface connector |
| FAN |
Microprocessor fan connector |
| FRONTAUDIO |
Front-panel audio connector for onboard
audio |
| FRONTPANEL |
Front-panel cable connector |
| IDEn |
EIDE interface connector |
| KYBD_MOUSE |
Keyboard and mouse connectors |
| MICROPROCESSOR |
Microprocessor connector |
| MODEM |
Telephony connector |
| MONITOR |
Video connector |
| NIC_USB |
Integrated NIC connector and USB
connectors |
| PAR_SER1_SER2 |
Parallel and serial port connectors |
| PCI1 and 2 |
PCI expansion card connectors |
| POWER |
Main power input connector |
| PSWD |
Password jumper |
| VRISER |
Riser board connector |
| SPEAKER |
Internal speaker |
| VRM |
Voltage regulator module connector (may
not be removable on some systems) |
Removing DIMMs
- Press the securing clips outward simultaneously until the memory
module disengages and pops out slightly from the socket.
- Lift the module away from the socket.
Replacing DIMMs
- Press the module fully into the socket while closing the securing
clips to lock the module into place.
 |
| 1 |
Securing clips (2) |
| 2 |
Slot |
|
- Close the computer cover,
reconnect your computer and peripherals to their electrical outlets, and turn them on.
|
NOTE: After you open and close the cover,
the chassis intrusion detector causes the following message to appear on the screen at the
next system start-up:
ALERT! Cover was previously removed.You will need to reset the chassis intrusion
detector. |
The system detects that the new memory does not match the existing
system configuration information and generates the following message:
The amount of system memory has changed.
Strike the F1 key to continue, F2 to run the setup utility
- Press <F2> to enter system setup, and check the value for System
Memory.
The system should have already changed the
value of System Memory to reflect the newly installed memory. Verify the
new total. If it is correct, skip to step 5.
- If the memory total is incorrect, turn off and disconnect your
computer and peripherals from their electrical outlets. Open the
computer cover, and check the installed DIMMs to make sure that they are seated
properly in their sockets. Then repeat steps 2, 3, and 4.
- Reset the chassis intrusion detector by
changing Chassis Intrusion to Enabled or
Enabled-Silent.
|
NOTE: If a setup password has been
assigned by someone else, contact your network administrator for information on resetting
the chassis intrusion detector.
|
- When the System Memory total is correct, press
<Esc> to exit system setup.
- Run the Dell Diagnostics to verify that the DIMMs are operating
properly.
Installing an AGP Card
|
NOTE: The small form-factor and small
desktop systems support low-profile AGP cards. |
- Remove the filler bracket by raising the hinged lever and sliding the
bracket up.
Removing the AGP Slot Filler Bracket in the
Small-Form Factor System
Removing the AGP Slot Filler Bracket—Small Desktop
System
Removing the AGP Slot Filler Bracket—Small Mini-Tower
System
- Insert the AGP card into the connector on the
system board. Make sure that the card is securely fastened by the AGP card clip.
Installing an AGP Card
 |
| 1 |
Front end notch of AGP card |
| 2 |
I/O panel AGP video connector |
| 3 |
AGP card clip lever |
|
- Press the AGP card clip lever toward the PCI
slots.
- Slide the AGP card into place.
- Release the AGP card clip lever, ensuring that the tab on the AGP
card clip lever fits into the notch on the front end of the AGP card.
- Secure the AGP card bracket by lowering the securing lever on the
back panel.
Removing an AGP Card
- Raise the hinged lever on the back on
the system.
- On the AGP card clip, press the lever toward the PCI
slots.
- Pull the AGP card up out of the AGP card clip.
Installing a GPA (AIMM) Card
 |
| 1 |
Front end of GPA card |
| 2 |
Back end of GPA card |
| 3 |
GPA connector |
| 4 |
AGP card clip tab |
| 5 |
AGP card clip |
| 6 |
AGP card clip lever tab |
| 7 |
AGP card clip lever |
|
- Insert the card into the connector.
- Hook the back end of the card under the AGP card clip tab.
- Lower the front end of the card, and push the AGP card clip lever
away so that the AGP card clip lever tab is out of the way.
- Insert the card firmly into the connector, and release the lever so
that the tab is over the front end card bottom.
Removing a GPA (AIMM) Card
- Press on the AGP card clip lever so that the tab is not covering the
card edge bottom.
- Lift the card's front end up, and slightly tilt it upward until the
other card end is free from the AGP card clip tab.
- Open the computer cover.
|
CAUTION: The microprocessor and heat-sink
assembly can get extremely hot. Be sure the assembly has had sufficient time to cool
before you touch it. |
- Disconnect the cooling fan power cable from the FAN1 connector on the
system board.
- On the small mini-tower system, remove the airflow shroud as
shown in the following illustration.
- Remove the cooling-fan/heat-sink assembly.
Your system has one of two types of heat-sink clip—a
green-tabbed clip or a toggle clip.
- For systems with the green-tabbed clip, press down on the
inside edge of the green tab as shown in the following illustration. Remove the clip from
the socket, and then remove the heat sink from the microprocessor.
- For systems with the toggle clip, remove
the DIMM closest to the microprocessor heat-sink assembly. Pull down on the toggle
clip lever until you can unhook the ends of the clip from the tabs on each side of the ZIF
socket. Remove the clip from the socket, and then lift the heat sink from the
microprocessor.
 |
| 1 |
Heat sink |
| 2 |
Toggle clip lever |
| 3 |
ZIF socket tabs (2) |
|
- Remove the microprocessor chip from the socket.
NOTICE: Be careful not to bend any of the pins when you remove
the microprocessor package from the ZIF socket. Bending the package pins can permanently
damage the microprocessor.
The ZIF socket has a lever-type handle that secures and releases the microprocessor
package from the ZIF socket.
- Pull the socket release lever straight up until the microprocessor
package releases.
- Remove the microprocessor package from the socket.
Leave the release lever extended so that the socket is ready for the
new microprocessor package.
Removing the Microprocessor
 |
| 1 |
Microprocessor chip |
| 2 |
Socket release lever |
| 3 |
ZIF socket |
|
NOTICE: Ground yourself by touching an unpainted metal
surface on the back of the computer.
NOTICE: If you are replacing the microprocessor, do not reuse the
old heat sink. Doing so can cause the microprocessor to overheat because of an inadequate
amount of thermal compound between the heat-sink assembly and the microprocessor package.
NOTICE: You must position the microprocessor package correctly in
the ZIF socket to avoid permanent damage to the microprocessor and the computer when you
turn on the system.
- Install the microprocessor package in the ZIF socket.
- If the release lever on the ZIF socket is not all the way out, move
it to that position now.
- Align pin-1 (the beveled corner) of the microprocessor package and
pin-1 of the ZIF socket.
Installing the Microprocessor Chip
 |
| 1 |
Pin-1 corners of chip and socket aligned |
|
- Set the microprocessor package lightly in the socket, making sure
that all the pins are headed into the correct holes.
Because the system uses a ZIF socket, there is no need to use force (which could bend the
pins if the microprocessor package is misaligned).
- When the microprocessor package is positioned correctly, press it
with minimal pressure to fully seat it in the ZIF socket.
- When the microprocessor package is fully seated, pivot the release
lever back toward the system board until it snaps into place, securing the microprocessor
package.
- Replace the cooling-fan/heat-sink assembly.
- If you are installing a new cooling-fan/heat-sink assembly, remove
the plastic cover that is attached to the bottom of the new cooling fan/heat-sink
assembly.
- Place the cooling-fan/heat-sink assembly on top of the microprocessor
package.
- Orient the securing clip so that the tab is facing the memory
modules, and hook both ends of the securing clip over the ZIF socket tabs.
- If your system has the toggle clip, rotate the lever upward until it
snaps into place. Then replace the DIMM you removed earlier.
|
NOTE: If you are installing a microprocessor replacement kit from Dell, return the original heat-sink assembly and microprocessor package to Dell in the same package in which your replacement kit was sent. Your
microprocessor replacement kit should include a replacement microprocessor heat sink. |
- If you have a mini-tower system, replace the airflow shroud.
- Reconnect the cooling fan power cable to the FAN1 connector on the
system board.
As the system boots, it detects the presence of the new
microprocessor and automatically changes the system configuration information in system
setup.
| |
NOTE: After you open and close the
cover, the chassis intrusion detector causes the following message to be displayed at the
next system start-up:
ALERT! Cover was previously removed. |
- Enter system setup and confirm that the system data area correctly
identifies the type of installed microprocessor.
| |
NOTE: For instructions on using system setup, see
the online System User's Guide |
- While in system setup, reset the Chassis Intrusion option by
pressing the left- or right-arrow key to select Reset and then choosing Enabled,
Enabled-Silent, or Disabled.
| |
NOTE: If a setup password has been assigned by
someone else, contact the network administrator for information on resetting the chassis
intrusion detector. |
- Run the Dell Diagnostics to verify that the new processor is
operating correctly.
Earlier GX150 systems contain a removable voltage regulator module
(VRM). If your microprocessor upgrade kit comes with a VRM, perform the following steps:
|
NOTE: The VRM cannot be removed on
some systems. |
NOTICE: If you use a flat-head screwdriver to press on the levers, be very careful to
not let the screwdriver slip and damage system board components.
- To remove the VRM, press on the levers of the VRM connector until the
module is released and pops up. Since there is not much room between the microprocessor
heat sink and the VRM, you may have to use a flat-head screwdriver to press on the levers.
Removing the VRM
 |
| 1 |
VRM |
| 2 |
VRM connector |
| 3 |
Levers (2) |
|
- Install the VRM by inserting it into the connector until
you hear the module snap into place.
|
CAUTION: There is a danger of the new battery
exploding if it is incorrectly installed. Replace the battery only with the same or
equivalent type recommended by the manufacturer. Discard used batteries according to the
manufacturer’s instructions. |
- If possible, enter system setup and print the system setup screens.
- Remove the system battery by carefully prying it out of its socket
with your fingers or with a blunt, nonconducting object such as a plastic screwdriver.
Replacing the System Battery
- Orient the new battery with the "+" facing up.
- Insert the battery into its socket and snap it into place.
Removing the System
Board—Small Form-Factor Desktop, Small Desktop, and Small Mini-Tower Systems
 |
| 1 |
System board and metal tray assembly |
| 2 |
Tab |
|
| |
NOTE: The system board and the metal tray
are attached and are removed as one piece. |
- Remove or move any components that restrict access to the
system board.
- Disconnect all cables from the system board.
Before you remove the existing system board, visually compare the replacement system board
to the existing system board to make sure that you have the correct part.
| |
NOTE: The small mini-tower system has a tab
on the riser board. Release the tab before you remove the system board. |
- Pull up on the tab and slide the system board toward the front of the
chassis; lift it up and away.
- Place the system board that you just removed next to the replacement
system board.
Replacing the System Board
- Transfer components from the existing system board to the replacement
system board.
- Remove the memory modules and install them on the replacement board.
|
CAUTION: The microprocessor package
and heat-sink assembly can get hot. To avoid burns, be sure that the package and assembly
have had sufficient time to cool before you touch them.
|
- Remove the fan/heat-sink assembly and microprocessor package from the
existing system board and transfer it to the replacement system board.
- For the small mini-tower replace the riser
board.
- Configure the settings of the replacement system board.
Set the jumper on the replacement system board so it is identical to the one on the
existing board.
| |
NOTE: Some components and connectors on the
replacement system board may be in different locations than the corresponding connectors
on the existing system board. |
- Orient the replacement board by aligning the notches on the bottom to
the tabs on the chassis floor.
- Slide the board toward the back of the chassis until it clicks into
place.
- Replace any components and cables that you removed from the system
board.
- Reconnect all cables to their connectors at the back of the computer,
close the computer cover, and reconnect the computer and
devices to their power sources and turn them on.
| |
NOTE: After you close the
cover, the chassis intrusion detector causes the following message to be displayed at the
next system start-up:
ALERT! Cover was previously removed. |
- Reset the chassis intrusion detector.
Back to Contents Page
| 
