Use the front USB connectors for devices that you connect occasionally, such as joysticks or cameras, or for bootable USB devices (see System Setup for more information about booting to a USB device).
It is recommended that you use the back USB connectors for devices that typically remain connected, such as printers and keyboards.
2
power button
Press to turn on the computer.
NOTICE: To avoid losing data, do not turn off the computer by pressing the power button. Instead, perform an operating system shutdown. See Turning Off Your Computer for more information.
NOTICE: If your operating system has ACPI enabled, when you press the power button the computer will perform an operating system shutdown.
3
Dell badge
Can be rotated to match the orientation of your computer. To rotate, place fingers around the outside of the badge, press firmly, and turn the badge. You can also rotate the badge using the slot provided near the bottom of the badge.
4
LAN indicator light
Indicates that a LAN (local area network) connection is established.
5
diagnostic lights
Use the lights to help you troubleshoot a computer problem based on the diagnostic code. For more information, see Diagnostic Lights.
6
hard drive activity light
This light flickers when the hard drive is being accessed.
7
power light
The power light illuminates and blinks or remains solid to indicate different operating states:
No light — The computer is turned off.
Steady green — The computer is in a normal operating state.
Blinking green — The computer is in a power-saving mode.
To exit from a power-saving mode, press the power button or use the keyboard or the mouse if it is configured as a wake device in the Windows Device Manager. For more information about sleep modes and exiting from a power-saving mode, see Power Management for Windows XP and Windows Vista.
See Dell Diagnostics for a description of light codes that can help you troubleshoot problems with your computer.
8
headphone connector
Use the headphone connector to attach headphones and most kinds of speakers.
9
microphone connector
Use the microphone connector to attach a microphone.
10
3.5-inch drive bay
Can contain an optional slimline floppy drive or optional media card reader.
11
5.25-inch drive bay
Can contain a slimline optical drive. Insert a CD or DVD (if supported) into this drive.
Back View
1
card slots
Access connectors for any installed PCI cards, PCI Express cards, PS/2, eSATA, and so on.
2
back panel connectors
Plug serial, USB, and other devices into the appropriate connectors (see Back Panel Connectors).
3
power connector
Insert the power cable.
4
voltage selection switch
Your computer is equipped with a manual voltage-selection switch. To help avoid damaging a computer with a manual voltage selection switch, set the switch for the voltage that most closely matches the AC power available in your location.
NOTICE: In Japan, the voltage selection switch must be set to the 115-V position.
Also, ensure that your monitor and attached devices are electrically rated to operate with the AC power available in your location.
5
padlock ring
Insert a padlock to lock the computer cover.
6
cover release latch
Allows you to open the computer cover.
Back Panel Connectors
1
parallel connector
Connect a parallel device, such as a printer, to the parallel connector. If you have a USB printer, plug it into a USB connector.
NOTE: The integrated parallel connector is automatically disabled if the computer detects an installed card containing a parallel connector configured to the same address. For more information, see System Setup Options.
2
link integrity light
Green — A good connection exists between a 10-Mbps network and the computer.
Orange — A good connection exists between a 100-Mbps network and the computer.
Yellow — A good connection exists between a 1-Gbps (or 1000-Mbps) network and the computer.
Off — The computer is not detecting a physical connection to the network.
3
network adapter connector
To attach your computer to a network or broadband device, connect one end of a network cable to either a network jack or your network or broadband device. Connect the other end of the network cable to the network adapter connector on the back panel of your computer. A click indicates that the network cable has been securely attached.
NOTE: Do not plug a telephone cable into the network connector.
For VPro to work, the network cable must be connected to the onboard NIC.
It is recommended that you use Category 5 wiring and connectors for your network. If you must use Category 3 wiring, force the network speed to 10 Mbps to ensure reliable operation.
4
network activity light
Flashes a yellow light when the computer is transmitting or receiving network data. A high volume of network traffic may make this light appear to be in a steady "on" state.
5
line-out connector
Use the green line-out connector (available on computers with integrated sound) to attach headphones and most speakers with integrated amplifiers.
6
line-in/microphone connector
Use the blue and pink line-in/microphone connector (available on computers with integrated sound) to attach a record/playback device such as a cassette player, CD player, or VCR; or a personal computer microphone for voice or musical input into a sound or telephony program.
7
USB 2.0 connectors (6)
Use the back USB connectors for devices that typically remain connected, such as printers and keyboards.
8
video connector
Plug the cable from your VGA-compatible monitor into the blue connector.
NOTE: If you purchased an optional graphics card, this connector will be covered by a cap. Connect your monitor to the connector on the graphics card. Do not remove the cap.
NOTE: If you are using a graphics card that supports dual monitors, use the y-cable that came with your computer.
9
serial connector
Connect a serial device, such as a handheld device, to the serial port.
If you have installed a padlock through the padlock ring on the back panel, remove the padlock.
Locate the cover release latch shown in the illustration. Then, slide the release latch back as you lift the
cover.
Grip the sides of the computer cover and pivot the cover up using the bottom hinges as leverage
points.
Remove the cover from the hinge tabs and set it aside on a soft nonabrasive surface.
CAUTION: Graphics card heat sinks can become very hot during normal operation. Ensure that a graphics card heat sink has had sufficient time to cool before you touch it.
1
security cable slot
2
cover release latch
3
computer cover
Inside Your Computer
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
CAUTION: To avoid electrical shock, always unplug your computer from the electrical outlet before removing the computer cover.
NOTICE: Be careful when opening the computer cover to ensure that you do not accidentally disconnect cables from the system board.
1
drive-release latch
4
hard drive
2
optical drive
5
system board
3
power supply and fan
6
heat sink assembly
Chassis Intrusion Switch
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide.
NOTE: The chassis intrusion switch is standard on the ultra small form factor computer but is optional on mini tower, desktop, and small form factor computers; it may not be present on your computer.
Disconnect the chassis intrusion switch cable from the system board by using two fingers to squeeze
the release mechanism on one side of the connector as you pull to disconnect the cable connector.
Slide the chassis intrusion switch out of its slot in the metal bracket, and then push it down through
the square hole in the bracket to remove the switch and its attached cable from the computer.
NOTE: You may feel a slight resistance as you slide the switch out of the slot.
Replacing the Chassis Intrusion Switch
Gently insert the switch from underneath the metal bracket into the square hole in the bracket, and
then slide the chassis intrusion switch into its slot until it snaps securely into place.
If you are using a computer stand, attach it to the computer.
Resetting the Chassis Intrusion Detector
Turn on (or restart) your computer.
When the blue DELL™ logo appears, press <F2> immediately.
If you wait too long and the operating system logo appears, continue to wait until you see the Microsoft® Windows® desktop. Then shut down your computer and try again.
Select the Chassis Intrusion option and then press the left- or right-arrow key to select Reset. Change
the setting to On, On-Silent, or Disabled.
