Back to Contents Page

Display

Dell™ Latitude™ 110L Service Manual

  Display Assembly

  Display Bezel

  Display Panel


Display Assembly

CAUTION: Before performing the following procedures, read the safety instructions in the Product Information Guide.
CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface.
  1. Follow the instructions in "Before Working Inside Your Computer."

  2. Remove the keyboard.

  3. Disconnect the display ground wire from the EMI shield by unscrewing the captive screw.

1

captive screw

2

display ground wire

  1. Remove the four M2.5 x 5-mm screws (labeled "M2.5x5") that secure the EMI shield to the system board.

  2. Pull the EMI shield out of the computer baseby rotating the front upwards then lifting to release the retention tabs from the retention-tab slots.

1

M2.5 x 5-mm screws (4)

2

shield retention tabs (3)

3

shield-retention tab slots

  1. Disconnect the attached antenna cable from the Mini PCI card.

1

antenna cable

2

metal securing tabs (2)

3

Mini PCI card connector

4

Mini PCI card

  1. Close the display.

  2. From the bottom of the computer, remove the two M2.5 x 5-mm screws labeled "D."

  1. From the back of the computer, remove the two M2.5 x 8-mm screws labeled "D."

  1. Pull straight up on the pull-tab that is attached to the display-feed flex cable to disconnect the cable from the system board.

1

display cable

2

system board connector

  1. Carefully remove the Mini PCI card antenna cable and the display cables from their routing guides.

  2. Lift the display assembly out of the computer base.

1

screw covers/display bumpers (6)

2

display bezel

3

M2.5 x 5-mm screws (6)

4

display panel

5

M2 x 3-mm screws (8)

6

top cover

7

display-feed flex cable

Display Bezel

CAUTION: Before performing the following procedures, read the safety instructions in the Product Information Guide.
CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface.
  1. Follow the instructions in "Before Working Inside Your Computer."

  2. Remove the display assembly.

  3. Use a plastic scribe to pry the six screw covers/display bumpers out of the screw holes on the front of the bezel.

  4. Remove the six M2.5 x 5-mm screws from the front of the bezel.

NOTICE: Carefully separate the bezel from the top cover to avoid damage to the bezel.
  1. Starting at the bottom of the display panel, use your fingers to separate the bezel from the top cover and lift the inside edge of the bezel away from the top cover.

Display Panel

Removing the Display Panel

CAUTION: Before performing the following procedures, read the safety instructions in the Product Information Guide.
CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface.
  1. Follow the instructions in "Before Working Inside Your Computer."

  2. Remove the display assembly.

  3. Remove the display bezel.

  4. Remove the four M2 x 3-mm screws from each side of the display panel.

  5. Lift the display panel out of the top cover.

  6. Press in both sides of the top flex-cable connector, and pull the top flex-cable connector away from the display connector.

1

inverter connector

2

pull-tab on bottom flex-cable connector

3

top flex-cable connector

4

display connector

  1. Use the pull-tab to disconnect the bottom flex-cable connector from the inverter connector.

Installing the Display Panel

  1. Connect the top flex-cable connector to the display panel connector.

  2. Connect the bottom flex-cable connector to the inverter connector.

  3. Lay the display panel into the top cover.

  4. Route the display-feed flex cable so that it rests in the notch located in the bottom edge of the top cover.

  5. Replace the eight M2 x 3-mm screws that secure the display panel to the top cover.

  6. Replace the display bezel.

Back to Contents Page