This chapter provides procedures for removing and installing the components in your computer. Unless otherwise noted, each procedure assumes that the following conditions exist:
You have read the safety information in your Dell Product Information Guide.
A component can be replaced—or if purchased separately—installed by performing the removal procedure in reverse order.
Recommended Tools
The procedures in this document may require the following tools:
Small flat-blade screwdriver
Phillips screwdriver
Small plastic scribe
Flash BIOS update (see the Dell Support website at support.dell.com)
Turning Off Your Computer
NOTICE: To avoid losing data, save and close any open files and exit any open programs before you turn off your computer.
Save and close any open files and exit any open programs.
Click Start , click the arrow , and then click Shut Down.
The computer turns off after the operating system shutdown process finishes.
Ensure that the computer and any attached devices are turned off. If your
computer and attached devices did not automatically turn off when you
shut down your operating system, press and hold the power button for at
least 8 to 10 seconds until the computer turns off.
Before Working Inside Your Computer
Use the following safety guidelines to help protect your computer from potential damage and to help ensure your own personal safety.
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its edges or by its metal mounting bracket. Hold a component such as a processor by its edges, not by its pins.
NOTICE: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell is not covered by your warranty.
NOTICE: When you disconnect a cable, pull on its connector or on its strain-relief loop, not on the cable itself. Some cables have a connector with locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep them evenly aligned to avoid bending any connector pins. Also, before you connect a cable, ensure that both connectors are correctly oriented and aligned.
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer).
NOTICE: To help prevent damage to the computer, perform the following steps before you begin working inside the computer.
Ensure that the work surface is flat and clean to prevent the computer
cover from being scratched.
NOTICE: To disconnect a network cable, first unplug the cable from your computer, and then unplug it from the network wall jack.
Disconnect any telephone or network cables from the computer.
Disconnect your computer and all attached devices from their electrical
outlets.
NOTICE: To help prevent damage to the system board, you must remove the battery from the battery bay before you service the computer.
NOTE: To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do not use batteries designed for other Dell computers.
Turn the computer over.
Slide and click the battery release latches.
Slide the battery out of the battery bay.
1
battery
2
battery release latch (2)
Turn the computer top-side up, open the display, and press the power
button to ground the system board.
Depending on the configuration you ordered, your computer may have two hard drives: a primary hard drive and an optional secondary hard drive.
CAUTION: If you remove the hard drive from the computer when the drive is hot, do not touch the metal housing of the hard drive.
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
NOTICE: To prevent data loss, turn off your computer (see Turning Off Your Computer) before removing the hard drive. Do not remove the hard drive while the computer is on or in Sleep state.
NOTICE: Hard drives are extremely fragile. Exercise care when handling the hard drive.
NOTE: Dell does not guarantee compatibility or provide support for hard drives from sources other than Dell.
Loosen the two captive screws and remove the cover on the hard drive bay.
1
captive screws (2)
2
hard drive cover
NOTICE: When the hard drive is not in the computer, store it in protective antistatic packaging (see "Protecting Against Electrostatic Discharge" in the Product Information Guide).
Using the pull-tab on the hard drive, pull the hard drive out of the hard
drive bay.
1
secondary hard drive bay
2
screws (3)
3
primary hard drive
4
pull-tab
Replacing the Hard Drive
Remove the new drive from its packaging.
Save the original packaging for storing or shipping the hard drive.
NOTICE: Use firm and even pressure to slide the drive into place. If you use excessive force, you may damage the connector.
NOTICE: If you are installing only one hard drive, ensure you install the new drive in the primary hard drive bay.
NOTE: The secondary hard drive is optional.
Place the hard drive into the bay and press down to fully seat it.
Replace and tighten the screws on the hard drive.
Replace the hard drive cover and tighten the screws.
Using a plastic scribe, push the notch to release the optical drive from the bay.
1
optical drive
2
notch
3
locking screw
Replacing the Optical Drive
Slide the optical drive into the bay.
Replace and tighten the locking screw.
Hinge Cover
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer).
NOTICE: To help prevent damage to the system board, you must remove the battery from the battery bay before you begin working inside the computer.
Removing the Hinge Cover
Follow the procedures in "Before You Begin" on page 137.
Open the display as far as it will open.
NOTICE: To avoid damage to the hinge cover, do not lift the cover on both sides simultaneously.
Insert a plastic scribe into the indent to lift the hinge cover on the right
side.
Ease the hinge cover up, moving from right to left, and remove it.
1
hinge cover
2
scribe
Replacing the Hinge Cover
Insert the left edge of the hinge cover.
Press from left to right until the cover snaps into place.
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer).
NOTICE: To help prevent damage to the system board, you must remove the battery from the battery bay before you begin working inside the computer.
Remove the four screws at the top of the keyboard.
NOTICE: The keycaps on the keyboard are fragile, easily dislodged, and time-consuming to replace. Be careful when removing and handling the keyboard.
Slide the keyboard toward the back of the computer to disengage the
notch on the keyboard from the tab on the base of the computer.
Lift and remove the keyboard.
1
keyboard
2
screws (4)
3
notch on keyboard
4
tab on computer base
Replacing the Keyboard
Hook the tabs and the keyboard connector along the front edge of the
keyboard into the palmrest, and place the notch on the top of the keyboard
on the tab on the base of the computer.
Keeping the keyboard flat against the computer base, slide the tabs on the
bottom of the keyboard under the palmrest, and ensure the tab on the
computer base slides into the notch on the top of the keyboard.
1
tabs (7)
2
keyboard connector
3
notch on keyboard
4
tab on computer base
5
palmrest
Replace the four screws on the top of the keyboard.
Memory
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
You can increase your computer memory by installing memory modules on the system board. See Specifications for information on the memory supported by your computer. Install only memory modules that are intended for your computer.
NOTE: Memory modules purchased from Dell are covered under your computer warranty.
Your computer has two user-accessible SODIMM sockets, one accessed from beneath the keyboard (DIMM A), and the other accessed from the bottom of the computer (DIMM B).
NOTICE: If your computer has only one memory module, install the memory module in the connector labeled "DIMMA."
NOTICE: If you need to install memory modules in two connectors, install a memory module in the connector labeled "DIMMA" before you install a module in the connector labeled "DIMMB."
Removing the DIMM A Memory Module
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer).
The DIMM A memory module is located under the keyboard.
NOTICE: To prevent damage to the memory module connector, do not use tools to spread the memory module securing clips.
Use your fingertips to carefully spread apart the securing clips on each end
of the memory module connector until the module pops up.
Remove the module from the connector.
1
memory module (DIMM A)
2
securing clips (2)
Replacing the DIMM A Memory Module
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer).
Align the notch in the module edge connector with the tab in the
connector slot.
Slide the module firmly into the slot at a 45-degree angle, and rotate the
module down until it clicks into place. If you do not feel the click, remove
the module and reinstall it.
NOTE: If the memory module is not installed properly, the computer may not boot. No error message indicates this failure.
1
tab
2
notch
Replace the keyboard and hinge cover.
Insert the battery into the battery bay, or connect the AC adapter to your
computer and an electrical outlet.
Turn on the computer.
As the computer boots, it detects the additional memory and automatically updates the system configuration information.
To confirm the amount of memory installed in the computer, click Start ® Help and Support® Dell System Information.
Removing the DIMM B Memory Module
The DIMM B memory module is located under the memory module cover on the bottom of the computer.
NOTICE: To prevent damage to the memory module connector, do not use tools to spread the memory module securing clips.
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer).
Use your fingertips to carefully spread apart the securing clips on each end
of the memory module connector until the module pops up.
Remove the module from the connector.
1
securing clips (2)
2
memory module
Replacing the DIMM B Memory Module
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer).
Align the notch in the module edge connector with the tab in the
connector slot.
Slide the module firmly into the slot at a 45-degree angle, and rotate the
module down until it clicks into place. If you do not feel the click, remove
the module and reinstall it.
NOTE: If the memory module is not installed properly, the computer may not boot. No error message indicates this failure.
1
tab
2
notch
NOTICE: If the cover is difficult to close, remove the module and reinstall it. Forcing the cover to close may damage your computer.
Replace the memory module cover.
Insert the battery into the battery bay, or connect the AC adapter to your
computer and an electrical outlet.
Turn on the computer.
As the computer boots, it detects the additional memory and automatically updates the system configuration information.
To confirm the amount of memory installed in the computer, click Start ® Help and Support® Dell System Information.
Subscriber Identity Module
Subscriber Identity Modules (SIM) identify users uniquely through an International Mobile Subscriber Identity.
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
NOTE: Only Cingular and Vodafone need a SIM. Verizon, Sprint, and Telus do not use SIMs.
Loosen the captive screws on the cover of the Mini Card compartment and
remove the cover.
1
captive screws (2)
2
cover
Disconnect the antenna cables from the WLAN card.
1
antenna cable connectors (2)
2
WLAN card
Release the WLAN card by pushing the metal securing tabs toward the
back of the computer until the card pops up slightly.
Lift the WLAN card out of its system board connector.
1
metal securing tabs (2)
2
WLAN card
Replacing a WLAN Card
NOTICE: The connectors are keyed to ensure correct insertion. If you feel resistance, check the connectors on the card and on the system board, and realign the card.
NOTICE: To avoid damage to the WLAN card, never place cables under the card.
Insert the WLAN card connector at a 45-degree angle into the system
board connector labeled "WLAN".
Press the other end of the WLAN card down into the securing tabs until
the card clicks into place.
Connect the appropriate antenna cables to the WLAN card you are installing:
If the WLAN card has two triangles on the label (white and black), connect the white antenna cable to the connector labeled "main" (white triangle), and connect the black antenna cable to the connector labeled "aux" (black triangle).
If the WLAN card has three triangles on the label (white, black, and gray), connect the white antenna cable to the white triangle, connect the black antenna cable to the black triangle, and connect the gray antenna cable to the gray triangle.
Secure unused antenna cables in the protective mylar sleeve.
Replace the cover and tighten the captive screws.
Removing a Mobile Broadband or WWAN Card
NOTE: WWAN is also available on an ExpressCard (see Using ExpressCards).
Loosen the captive screws on the cover of the Mini Card compartment and
remove the cover.
1
captive screws (2)
2
cover
Disconnect the two antenna cables from the WWAN card.
1
antenna cable connectors (2)
2
WWAN card
Release the WWAN card by pushing the metal securing tabs toward the
back of the computer until the card pops up slightly.
Lift the WWAN card out of its system board connector.
1
metal securing tabs (2)
2
WWAN card
Replacing a WWAN Card
NOTICE: The connectors are keyed to ensure correct insertion. If you feel resistance, check the connectors on the card and on the system board, and realign the card.
NOTICE: To avoid damage to the WWAN card, never place cables under the card.
Insert the WWAN card connector at a 45-degree angle into the system
board connector labeled "WWAN".
Press the other end of the WWAN card down into the securing tabs until
the card clicks into place.
Connect the black antenna cable with a gray stripe to the connector
labeled "aux" (black triangle) and connect the white antenna cable with a
gray stripe to the connector labeled "main" (white triangle).
Secure unused antenna cables in the protective mylar sleeve.
Loosen the captive screws on the cover of the Mini Card compartment and
remove the cover.
1
captive screws (2)
2
cover
Disconnect the blue antenna cable from the WPAN card.
Release the WPAN card by pushing the metal securing tabs toward the
back of the computer until the card pops up slightly.
Lift the WPAN card out of its system board connector.
Replacing a WPAN Card
NOTICE: The connectors are keyed to ensure correct insertion. If you feel resistance, check the connectors on the card and on the system board, and realign the card.
NOTICE: To avoid damage to the WPAN card, never place cables under the card.
Insert the WPAN card connector at a 45-degree angle into the system
board connector labeled "WPAN".
Press the other end of the WPAN card down into the securing tabs until
the card clicks into place.
Connect the blue antenna cable to the WPAN card.
Secure unused antenna cables in the protective mylar sleeve.
Replace the cover and tighten the captive screws.
Flash Cache Module
The Flash Cache Module (FCM) is an internal flash drive that helps improve the performance of your computer. If you ordered an FCM with your computer, the card is already installed.
Turn the computer over and remove the cover on the Mini Card
compartment.
Ground yourself by touching one of the metal connectors on the back of
the computer.
NOTE: If you leave the area, ground yourself again when you return to the computer.
Release the FCM by pushing the metal securing brackets away from the
card until the card pops up slightly.
Remove the FCM.
1
metal securing tabs (2)
2
FCM
Replacing the FCM
NOTICE: Install the FCM in the WWAN or WPAN slot. Do not install an FCM in the WLAN card slot. Doing so may cause damage to your computer.
Insert the FCM connector at a 45-degree angle into the system board
connector labeled "FCM".
Press the other end of the FCM down into the securing tabs until the card
clicks into place.
Internal Card With Bluetooth® Wireless
Technology
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer).
NOTICE: To help prevent damage to the system board, you must remove the battery from the battery bay before you begin working inside the computer.
If you ordered a card with Bluetooth wireless technology with your computer, it is already installed.
Grasp the connector end of the card and slide it out from under the
securing tabs.
1
securing tabs (2)
2
cable
3
card
Replacing the Card
Replace the card at an angle to slide it under the securing tabs in the card
compartment.
Connect the cable to the card.
Coin-Cell Battery
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer).
NOTICE: To help prevent damage to the system board, you must remove the battery from the battery bay before you begin working inside the computer.
, click the arrow 
