|
|
1
|
VESA mounting holes (100mm) (Behind attached base plate)
|
Use to mount the monitor.
|
|
2
|
Barcode serial number label
|
Refer to this label if you need to contact Dell for technical
support.
|
|
3
|
Security lock slot
|
Use a security lock with the slot to help secure your monitor.
|
|
4
|
Dell Soundbar mounting brackets
|
Attach the optional Dell Soundbar.
|
|
5
|
Regulatory rating label
|
List the regulatory approvals.
|
|
6
|
Stand removal button
|
Press to release the stand
|
|
7
|
Cable holder
|
Help organize cables by placing them in the holder.
|
|
8
|
Lock down/release button
|
Push the monitor down, press the button to unlock the monitor, and
then lift the monitor to the desired height.
|
|
1
|
Power connector
|
Insert the power cable.
|
|
2
|
Dell Soundbar power connector
|
Connect the power cord for the Soundbar (optional).
|
|
3
|
DVI connector
|
Connect your computer DVI cable.
|
|
4
|
VGA connector
|
Connect your computer VGA cable.
|
|
5
|
USB upstream connector
|
Connect the USB cable that came with your monitor to the monitor
and the computer. Once this cable is connected you can use the USB
connectors on the side and bottom of the monitor.
|
|
6
|
USB connector
|
Connect your USB devices.
|
 NOTE: You can use this
connector only after you connect the USB cable to the computer and the USB
upstream connector on the monitor.
|
|
USB connectors (downstream)
|
|
|
Left side
|
|
Right side
|
|
If you have VESA's DPM™ compliance display card or software installed
in your PC, the monitor can automatically reduce its power consumption when
not in use. This is referred to as 'Power Save Mode'*. If input from
keyboard, mouse, or other input devices is detected by the computer, the
monitor automatically 'wakes up'. The following table shows the power
consumption and signaling of this automatic power saving feature:
|
VESA Modes
|
Horizontal Sync
|
Vertical Sync
|
Video
|
Power Indicator
|
Power Consumption
|
|
Normal operation (with Dell Soundbar and USB active)
|
Active
|
Active
|
Active
|
Green
|
75 W (maximum)
|
|
Normal operation
|
Active
|
Active
|
Active
|
Green
|
32 W (typical)
|
|
Active-off mode
|
Inactive
|
Inactive
|
Blanked
|
Amber
|
Less than 2 W
|
|
Switch off
|
-
|
-
|
-
|
Off
|
Less than 1 W
|
|
|
NOTE: The OSD only functions in the 'normal operation' mode. One
of the following messages appears when the “menu” or “plus” buttons are
pressed when in Active-off mode.
|
|
1. Analog Input
In Power Save Mode
Press Computer Power Button
or Any Key on Keyboard or Move Mouse |
or
|
2. Digital Input
In Power Save Mode
Press Computer Power Button
or Any Key on Keyboard or Move Mouse |
Activate the computer and 'wake up' the monitor to gain access to the OSD.
|
This monitor is ENERGY STAR®-compliant as well as TCO '99 /
TCO '03 power management compatible.
|
|
* Zero power consumption in OFF mode can only be achieved by
disconnecting the main cable from the monitor.
15-pin D-Sub connector
|
Pin Number
|
Monitor Side of the 15-pin Side Signal Cable
|
|
1
|
Video-Red
|
|
2
|
Video-Green
|
|
3
|
Video-Blue
|
|
4
|
GND
|
|
5
|
Self-test
|
|
6
|
GND-R
|
|
7
|
GND-G
|
|
8
|
GND-B
|
|
9
|
DDC +5V
|
|
10
|
GND-sync
|
|
11
|
GND
|
|
12
|
DDC data
|
|
13
|
H-sync
|
|
14
|
V-sync
|
|
15
|
DDC clock
|
24-pin Digital-only DVI Connector
Note: Pin 1 is at the top right.
|
Pin
|
Signal Assignment
|
Pin
|
Signal Assignment
|
Pin
|
Signal Assignment
|
|
1
|
T.M.D.S. Data 2-
|
9
|
T.M.D.S. Data 1-
|
17
|
T.M.D.S. Data 0-
|
|
2
|
T.M.D.S. Data 2+
|
10
|
T.M.D.S. Data 1+
|
18
|
T.M.D.S. Data 0+
|
|
3
|
T.M.D.S. Data 2 Shield
|
11
|
T.M.D.S. Data 1 Shield
|
19
|
T.M.D.S. Data 0 Shield
|
|
4
|
No Pin
|
12
|
No Pin
|
20
|
No Pin
|
|
5
|
No Pin
|
13
|
No Pin
|
21
|
No Pin
|
|
6
|
DDC Clock
|
14
|
+5V Power
|
22
|
T.M.D.S. Clock Shield
|
|
7
|
DDC Data
|
15
|
Ground (for +5V)
|
23
|
T.M.D.S. Clock +
|
|
8
|
No Connect
|
16
|
Hot Plug Detect
|
24
|
T.M.D.S. Clock -
|
|
This monitor supports High-Speed Certified USB 2.0 interface.
|
|
|
|
|
Data Rate
|
Power Consumption
|
|
High speed
|
480 Mbps
|
2.5W (Max., each port)
|
|
Full speed
|
12 Mbps
|
2.5W (Max., each port)
|
|
Low speed
|
1.5 Mbps
|
2.5W (Max., each port)
|
|
USB ports:
- 1 upstream - rear
- 4 downstream - 2 on rear; 2
on left side
|
|
NOTE: USB 2.0 capability requires 2.0-capable computer.
|
|
|
NOTE: The USB interface of the monitor works ONLY when monitor is
powered ON (or in Power Save Mode). Switching your monitor OFF and then ON
would re-enumerate its USB interface; attached peripherals may take a few
seconds to resume normal functionality.
|
You can install the monitor in any Plug and Play-compatible system.
The monitor automatically provides the computer system with its Extended
Display Identification Data (EDID) using Display Data Channel (DDC) protocols
so that the system can configure itself and optimize the monitor settings. If
desired, you can select different settings, but in most cases monitor
installation is automatic.
General
|
|
|
Model number
|
1907FP
|
|
|
|
|
|
|
Screen type
|
Active matrix - TFT LCD
|
|
Screen dimensions
|
19 inches (19-inch viewable image size)
|
|
Preset display area:
|
|
|
Horizontal
|
376 mm (14.8 inches)
|
|
Vertical
|
301 mm (11.9 inches)
|
|
Pixel pitch
|
0.294 mm
|
|
Viewing angle
|
130° (vertical) typ, 140° (horizontal) typ
|
|
Luminance output
|
300 CD/m ²(typ)
|
|
Contrast ratio
|
7 00 to 1 (typ)
|
|
Faceplate coating
|
Antiglare with hard-coating 3H
|
|
Backlight
|
CCFL (4) edgelight system
|
|
Response Time
|
8ms typical
|
|
|
|
|
|
|
Horizontal scan range
|
30 kHz to 81 kHz (automatic)
|
|
Vertical scan range
|
56 Hz to 76 Hz (automatic)
|
|
Optimal preset resolution
|
1280 x 1024 at 60 Hz
|
|
Highest preset resolution
|
1280 x 1024 at 75 Hz
|
|
|
Display Mode
|
Horizontal
Frequency (kHz)
|
Vertical Frequency
(Hz)
|
Pixel Clock (MHz)
|
Sync Polarity
(Horizontal/Vertical)
|
|
VESA, 720 x 400
|
31.5
|
70.0
|
28.3
|
-/+
|
|
VESA, 640 x 480
|
31.5
|
60.0
|
25.2
|
-/-
|
|
VESA, 640 x 480
|
37.5
|
75.0
|
31.5
|
-/-
|
|
VESA, 800 x 600
|
37.9
|
60.3
|
49.5
|
+/+
|
|
VESA, 800 x 600
|
46.9
|
75.0
|
49.5
|
+/+
|
|
VESA, 1024 x 768
|
48.4
|
60.0
|
65.0
|
-/-
|
|
VESA, 1024 x 768
|
60.0
|
75.0
|
78.8
|
+/+
|
|
VESA, 1152 x 864
|
67.5
|
75.0
|
108
|
+/+
|
|
VESA, 1280 x 1024
|
64.0
|
60.0
|
135.0
|
+/+
|
|
VESA, 1280 x 1024
|
80.0
|
75.0
|
135.0
|
+/+
|
|
|
|
|
|
|
|
Video input signals
|
Analog RGB, 0.7 Volts +/-5%, positive polarity at 75 ohm input
impedance
Digital DVI-D TMDS, 600mV for each differential line, positive polarity at 50
ohm input impedance
|
|
Synchronization input signals
|
Separate horizontal and vertical synchronizations, polarity-free
TTL level, SOG (Composite SYNC on green)
|
|
AC input voltage / frequency / current
|
100 to 240 VAC / 50 or 60 Hz + 3 Hz / 2.0A (Max.)
|
|
Inrush current
|
120V:42A (Max.)
240V:80A (Max.)
|
|
|
|
|
|
|
Connector type
|
15-pin D-subminiature, blue connector; DVI-D, white connector
|
|
Signal cable type
|
Digital: Detachable, DVI-D, Solid pins, shipped detached from the
monitor
Analog: Detachable, D-Sub, 15pins, shipped attached to the monitor
|
|
Dimensions (with stand):
|
|
|
Height (Compressed)
|
14.11 inches (358.33 mm)
|
|
Height
(Extended)
|
19.23 inches (488.56 mm)
|
|
Width
|
16.15 inches (410.10 mm)
|
|
Depth
|
7.16 inches (181.90 mm)
|
|
Dimensions: (without stand)
|
|
|
Height
|
13.31 inches (338.04 mm)
|
|
Width
|
16.15 inches (410.10 mm)
|
|
Depth
|
2.60 inches (66.00 mm)
|
|
Stand dimensions:
|
|
|
Height (Compressed)
|
13.57 inches (344.70 mm)
|
|
Height (Extended)
|
15.30 inches (388.60 mm)
|
|
Width
|
13.27 inches (337.00 mm)
|
|
Depth
|
7.16 inches (181.90 mm)
|
|
Weight with packaging
|
18.96 lbs (8.6 kg)
|
|
Weight with stand assembly and cables
|
15.6 lbs (7.1 kg)
|
|
Weight without stand assembly
(For wall mount or VESA mount considerations - no cables)
|
11.02 lbs (5.0 kg)
|
|
Weight of stand assembly
|
3.53 lbs (1.60 kg)
|
|
|
|
|
|
|
Temperature:
|
|
|
Operating
|
5° to 35°C (41° to 95°F)
|
|
Nonoperating
|
Storage: -20° to 60°C (-4° to 140°F)
Shipping: -20° to 60°C(-4° to 140°F)
|
|
Humidity:
|
|
|
Operating
|
10% to 80% (noncondensing)
|
|
Nonoperating
|
Storage: 5% to 90% (noncondensing)
Shipping: 5% to 90%(noncondensing)
|
|
Altitude:
|
|
|
Operating
|
3,657.6m (12,000 ft) max
|
|
Nonoperating
|
12,192 m (40,000 ft) max
|
|
Thermal dissipation
|
256.08 BTU/hour (maximum)
119.5 BTU/hour (typical)
|
|
|
CAUTION: Read and follow the safety instructions before
cleaning the monitor.
|
|
|
CAUTION: Before cleaning the monitor, unplug the monitor power
cable from the electrical outlet.
|
- To clean your antistatic
screen, lightly dampen a soft, clean cloth with water. If possible, use
a special screen-cleaning tissue or solution suitable for the antistatic
coating. Do not use benzene, thinner, ammonia, abrasive cleaners, or
compressed air.
- Use a lightly-dampened, warm
cloth to clean the plastics. Avoid using detergent of any kind as some
detergents leave a milky film on the plastics.
- If you notice a white powder
when you unpack your monitor, wipe it off with a cloth. This white
powder occurs during the shipping of the monitor.
- Handle your monitor
with care as darker-colored plastics may scratch and show white scuff
marks more than lighter-colored monitor.
- To help maintain the best
image quality on your monitor, use a dynamically changing screen saver
and power off your monitor when not in use.
Back to Contents Page
|
