Connect the power cord for the Soundbar (optional).
3
DVI connector
Connect your computer DVI cable.
4
VGA connector
Connect your computer VGA cable.
5
USB upstream connector
Connect the USB cable that came with your monitor to the monitor
and the computer. Once this cable is connected you can use the USB
connectors on the side and bottom of the monitor.
6
USB connector
Connect your USB devices.
NOTE: You can use this
connector only after you connect the USB cable to the computer and the USB
upstream connector on the monitor.
If you have VESA's DPM™ compliance display card or software installed
in your PC, the monitor can automatically reduce its power consumption when not
in use. This is referred to as 'Power Save Mode'*. If input from keyboard,
mouse, or other input devices is detected by the computer, the monitor
automatically 'wakes up'. The following table shows the power consumption and
signaling of this automatic power saving feature:
VESA Modes
Horizontal Sync
Vertical Sync
Video
Power Indicator
Power Consumption
Normal operation (with Dell Soundbar and USB active)
Active
Active
Active
Green
75 W (maximum)
Normal operation
Active
Active
Active
Green
32 W (typical)
Active-off mode
Inactive
Inactive
Blanked
Amber
Less than 2 W
Switch off
-
-
-
Off
Less than 1 W
NOTE: The OSD will only function in the 'normal operation' mode.
One of the following messages will appear when the “menu” or “plus” buttons
are pressed when in Active-off mode.
1. Analog Input
In Power Save Mode
Press Computer Power Button
or Any Key on Keyboard or Move Mouse
or
2. Digital Input
In Power Save Mode
Press Computer Power Button
or Any Key on Keyboard or Move Mouse
Activate the computer
and 'wake up' the monitor to gain access to the OSD.
This monitor is ENERGY STAR�-compliant as well as TCO '99 /
TCO '03 power management compatible.
* Zero power consumption in OFF mode can only be achieved by
disconnecting the main cable from the monitor.
This monitor supports High-Speed Certified USB 2.0 interface.
Data Rate
Power Consumption
High speed
480 Mbps
2.5W (Max., each port)
Full speed
12 Mbps
2.5W (Max., each port)
Low speed
1.5 Mbps
2.5W (Max., each port)
USB ports:
1 upstream - rear
4 downstream - 2 on rear; 2
on left side
NOTE: USB 2.0 capability requires 2.0-capable computer.
NOTE: The USB interface of the monitor works ONLY when monitor is powered
ON (or in Power Save Mode). Switching your monitor OFF and then ON would
re-enumerate its USB interface; attached peripherals may take a few seconds
to resume normal functionality.
You can install the monitor in any Plug and Play-compatible system.
The monitor automatically provides the computer system with its Extended
Display Identification Data (EDID) using Display Data Channel (DDC) protocols
so that the system can configure itself and optimize the monitor settings. If
desired, you can select different settings, but in most cases monitor
installation is automatic.
Analog RGB, 0.7 Volts +/-5%, positive polarity at 75 ohm input
impedance
Digital DVI-D TMDS, 600mV for each differential line, positive polarity at
50 ohm input impedance
Synchronization input signals
Separate horizontal and vertical synchronizations, polarity-free
TTL level, SOG (Composite SYNC on green)
CAUTION: Read and follow the safety instructions before
cleaning the monitor.
CAUTION: Before cleaning the monitor, unplug the monitor power
cable from the electrical outlet.
To clean your antistatic screen,
lightly dampen a soft, clean cloth with water. If possible, use a
special screen-cleaning tissue or solution suitable for the antistatic
coating. Do not use benzene, thinner, ammonia, abrasive cleaners, or
compressed air.
Use a lightly-dampened, warm
cloth to clean the plastics. Avoid using detergent of any kind as some
detergents leave a milky film on the plastics.
If you notice a white powder
when you unpack your monitor, wipe it off with a cloth. This white
powder occurs during the shipping of the monitor.
Handle your monitor
with care as darker-colored plastics may scratch and show white scuff
marks more than lighter-colored monitor.
To help maintain the best image
quality on your monitor, use a dynamically changing screen saver and
power off your monitor when not in use.
