General
|
| Manufacturer: |
Quantum Corporation |
| Model
number: |
Atlas 10K |
| Interface: |
SCSI 160/m |
Capacity:
| Model |
Capacity |
Total LBAs |
| Atlas 10K 9.1 GB SCSI |
9.1 GB |
17,783,249 |
| Atlas 10K 18.2 GB SCSI |
18.2 GB |
35,566,499 |
| Atlas 10K 36.4 GB SCSI |
36.4 GB |
71,132,998 |
NOTE: The formatted capacity of your hard disk drive
may seem smaller than what you ordered because the operating system reports
drive capacity assuming that 1 megabyte (MB) equals 1,048,576 (2^20) bytes
while drive manufacturers consider 1 MB to equal 1,000,000
(10^6) bytes. |
|
Performance
|
| Rotational
Speed: |
10,000 RPM |
| Average Rotational
Latency: |
3.0 ms |
| Spin-up time to Ready (typical): |
15 Seconds |
| Cache: |
2 MB |
Typical Seek
time (without command overhead, including settling):
| Activity |
Specification |
| Track-to-Track |
0.8 ms |
| Average Random Read |
5.0 ms |
| Average Random Write |
5.5 ms |
| Full Stroke |
13.5 ms |
|
| Interface transfer
rate (max.): |
160 MB/Sec burst |
| Interleave
Factor: |
1:1 |
|
Internal
Characteristics
|
Number
of disks/heads:
| Model |
Disks |
Heads |
| Atlas 10K 9.1 GB SCSI |
3 |
6 |
| Atlas 10K 18.2 GB SCSI |
6 |
12 |
| Atlas 10K 36.4 GB SCSI |
12 |
24 |
|
| Track Density: |
13,060 tracks per inch |
| Bytes per sector |
512 |
|
Reliability
|
| Preventative
Maintenance: |
None Required |
| Non-recoverable
read errors: |
1 in 10^14 bits read |
| SMART compliant: |
Yes |
|
Electrical
|
| Nominal Voltage: |
+5 Vdc / +12 Vdc |
| Voltage Margin: |
+5Vdc @+/- 5%, +12Vdc @ +/- 5% |
|
Environmental
|
| Operating Temperature: |
5 to 55 degrees C |
| Operating Humidity: |
10 to 90% RH (non-condensing) |
| Non-operating Temperature: |
-40 to 70 degrees C |
| Non-operating Humidity: |
5 to 95% RH (non-condensing) |
|
Power Dissipation
|
|
9.1 GB |
18.2 GB |
36.4 GB |
| Startup (Peak) |
33.8W* |
33.8W* |
39W* |
| Idle |
10.3W |
10.3W |
14.9W |
| 40% Seek (ECMA) |
13.7W |
16.1W |
21.8W |
| Standby |
2.5W |
2.5W |
2.5W |
| Read/Write on Track |
12.2W |
12.2W |
18.9W |
*NOTE: Startup Peak Current measurements are performed based on
a 2.5ms sampling rate. The Industry typical sampling rate is 20ms
and therefore our Startup Peak power data will appear much higher than
the Industry typical numbers.
|
| EPA Energy Star Compliant: |
Yes |
|
Mechanical
Shock
|
| Operating (no data loss): |
15G @ 11 ms (half-sine) |
| Non-operating (no
data loss): |
200G @ 2 ms (half-sine) |
|
Physical
Characteristics
|
Atlas 10K 9.1 / 18.2 GB |
Atlas 10K 36.4 GB |
| Height: |
1.000" (25.4 mm) |
1.630" (41.4 mm) |
| Width: |
4.00" (101.6 mm) |
4.00" (101.6 mm) |
| Depth: |
5.75" (146.1 mm) |
5.75" (146.1 mm) |
| Weight: |
9.1 GB: 1.37 lbs. (0.6 kg)
18.2 GB: 1.45 lbs. (0.68 kg) |
2.4 lbs. (1.09 kg) |
|
|
