Server Administrator completed its initialization.
1002
A system BIOS update has been scheduled for the next reboot
Information
The user has chosen to update the flash basic input/output system (BIOS).
1003
A previously scheduled system BIOS update has been canceled
Information
The user decides to cancel the flash BIOS update, or an error occurs during the flash.
1004
Thermal shutdown protection has been initiated
Error
This message is generated when a system is configured for thermal shutdown due to an error event. If a temperature sensor reading exceeds the error threshold for which the system is configured, the operating system shuts down and the system powers off. This event may also be initiated on certain systems when a fan enclosure is removed from the system for an extended period of time.
1005
SMBIOS data is absent
Warning
The system does not contain the required systems management BIOS version 2.2 or higher, or the BIOS is corrupted.
1006
Automatic System Recovery (ASR) action was performed
Action performed was: <Action>
Date and time of action: <Date and time>
Error
This message is generated when an automatic system recovery action is performed due to a hung operating system. The action performed and the time of action are provided.
1007
User initiated host system control action
Action requested was: <Action>
Information
User requested a host system control action to reboot, power off, or power cycle the system. Alternatively the user had indicated protective measures to be initiated in the event of a thermal shutdown.
1008
Systems Management Data Manager Started
Information
Systems Management Data Manager services were started.
1009
Systems Management Data Manager Stopped
Information
Systems Management Data Manager services were stopped.
1011
RCI table is corrupt
Warning
This message is generated when the BIOS Remote Configuration Interface (RCI) table is corrupted or cannot be read by the systems management software.
1012
IPMI Status
Interface: <the IPMI interface being used>, <additional information if available and applicable>
Information
This message is generated to indicate the Intelligent Platform Management Interface (IPMI)) status of the system.
Additional information, when available, includes Baseboard Management Controller (BMC) not present, BMC not responding, System Event Log (SEL) not present, and SEL Data Record (SDR) not present.
Temperature Sensor Messages
Temperature sensors listed in Table 2-2 help protect critical components by alerting the systems management console when temperatures become too high inside a chassis. The temperature sensor messages use additional variables: sensor location, chassis location, previous state, and temperature sensor value or state.
Temperature sensor value (in degrees Celsius): <Reading>
If sensor type is discrete:
Discrete temperature state: <State>
Information
A temperature sensor on the backplane board, system board, or the carrier in the specified system failed. The sensor location, chassis location, previous state, and temperature sensor value are provided.
1051
Temperature sensor value unknown
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
If sensor type is not discrete:
Temperature sensor value (in degrees Celsius): <Reading>
If sensor type is discrete:
Discrete temperature state: <State>
Information
A temperature sensor on the backplane board, system board, or drive carrier in the specified system could not obtain a reading. The sensor location, chassis location, previous state, and a nominal temperature sensor value are provided.
1052
Temperature sensor returned to a normal value
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Previous state was: <State>
If sensor type is not discrete:
Temperature sensor value (in degrees Celsius): <Reading>
If sensor type is discrete:
Discrete temperature state: <State>
Information
A temperature sensor on the backplane board, system board, or drive carrier in the specified system returned to a valid range after crossing a failure threshold. The sensor location, chassis location, previous state, and temperature sensor value are provided.
1053
Temperature sensor detected a warning value
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Previous state was: <State>
If sensor type is not discrete:
Temperature sensor value (in degrees Celsius): <Reading>
If sensor type is discrete:
Discrete temperature state: <State>
Warning
A temperature sensor on the backplane board, system board, CPU, or drive carrier in the specified system exceeded its warning threshold. The sensor location, chassis location, previous state, and temperature sensor value are provided.
1054
Temperature sensor detected a failure value
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Previous state was: <State>
If sensor type is not discrete:
Temperature sensor value (in degrees Celsius): <Reading>
If sensor type is discrete:
Discrete temperature state: <State>
Error
A temperature sensor on the backplane board, system board, or drive carrier in the specified system exceeded its failure threshold. The sensor location, chassis location, previous state, and temperature sensor value are provided.
1055
Temperature sensor detected a non-recoverable value
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Previous state was: <State>
If sensor type is not discrete:
Temperature sensor value (in degrees Celsius): <Reading>
If sensor type is discrete:
Discrete temperature state: <State>
Error
A temperature sensor on the backplane board, system board, or drive carrier in the specified system detected an error from which it cannot recover. The sensor location, chassis location, previous state, and temperature sensor value are provided.
Cooling Device Messages
Cooling device sensors listed in Table 2-3 monitor how well a fan is functioning. Cooling device messages provide status and warning information for fans in a particular chassis.
A fan sensor in the specified system is not functioning. The sensor location, chassis location, previous state, and fan sensor value are provided.
1101
Fan sensor value unknown
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Previous state was: <State>
Fan sensor value: <Reading>
Information
A fan sensor in the specified system could not obtain a reading. The sensor location, chassis location, previous state, and a nominal fan sensor value are provided.
1102
Fan sensor returned to a normal value
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Previous state was: <State>
Fan sensor value: <Reading>
Information
A fan sensor reading on the specified system returned to a valid range after crossing a warning threshold. The sensor location, chassis location, previous state, and fan sensor value are provided.
1103
Fan sensor detected a warning value
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Previous state was: <State>
Fan sensor value: <Reading>
Warning
A fan sensor reading in the specified system exceeded a warning threshold. The sensor location, chassis location, previous state, and fan sensor value are provided.
1104
Fan sensor detected a failure value
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Previous state was: <State>
Fan sensor value: <Reading>
Error
A fan sensor in the specified system detected the failure of one or more fans. The sensor location, chassis location, previous state, and fan sensor value are provided.
1105
Fan sensor detected a non-recoverable value
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Previous state was: <State>
Fan sensor value: <Reading>
Error
A fan sensor detected an error from which it cannot recover. The sensor location, chassis location, previous state, and fan sensor value are provided.
Voltage Sensor Messages
Voltage sensors listed in Table 2-4 monitor the number of volts across critical components. Voltage sensor messages provide status and warning information for voltage sensors in a particular chassis.
A voltage sensor in the specified system failed. The sensor location, chassis location, previous state, and voltage sensor value are provided.
1151
Voltage sensor value unknown
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Previous state was: <State>
If sensor type is not discrete:
Voltage sensor value (in Volts): <Reading>
If sensor type is discrete:
Discrete voltage state: <State>
Information
A voltage sensor in the specified system could not obtain a reading. The sensor location, chassis location, previous state, and a nominal voltage sensor value are provided.
1152
Voltage sensor returned to a normal value
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Previous state was: <State>
If sensor type is not discrete:
Voltage sensor value (in Volts): <Reading>
If sensor type is discrete:
Discrete voltage state: <State>
Information
A voltage sensor in the specified system returned to a valid range after crossing a failure threshold. The sensor location, chassis location, previous state, and voltage sensor value are provided.
1153
Voltage sensor detected a warning value
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Previous state was: <State>
If sensor type is not discrete:
Voltage sensor value (in Volts): <Reading>
If sensor type is discrete:
Discrete voltage state: <State>
Warning
A voltage sensor in the specified system exceeded its warning threshold. The sensor location, chassis location, previous state, and voltage sensor value are provided.
1154
Voltage sensor detected a failure value
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Previous state was: <State>
If sensor type is not discrete:
Voltage sensor value (in Volts): <Reading>
If sensor type is discrete:
Discrete voltage state: <State>
Error
A voltage sensor in the specified system exceeded its failure threshold. The sensor location, chassis location, previous state, and voltage sensor value are provided.
1155
Voltage sensor detected a non-recoverable value
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Previous state was: <State>
If sensor type is not discrete:
Voltage sensor value (in Volts): <Reading>
If sensor type is discrete:
Discrete voltage state: <State>
Error
A voltage sensor in the specified system detected an error from which it cannot recover. The sensor location, chassis location, previous state, and voltage sensor value are provided.
Current Sensor Messages
Current sensors listed in Table 2-5 measure the amount of current (in amperes) that is traversing critical components. Current sensor messages provide status and warning information for current sensors in a particular chassis.
A current sensor on the power supply for the specified system failed. The sensor location, chassis location, previous state, and current sensor value are provided.
1201
Current sensor value unknown
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Previous state was: <State>
If sensor type is not discrete:
Current sensor value (in Amps): <Reading>
If sensor type is discrete:
Discrete current state: <State>
Information
A current sensor on the power supply for the specified system could not obtain a reading. The sensor location, chassis location, previous state, and a nominal current sensor value are provided.
1202
Current sensor returned to a normal value
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Previous state was: <State>
If sensor type is not discrete:
Current sensor value (in Amps): <Reading>
If sensor type is discrete:
Discrete current state: <State>
Information
A current sensor on the power supply for the specified system returned to a valid range after crossing a failure threshold. The sensor location, chassis location, previous state, and current sensor value are provided.
1203
Current sensor detected a warning value
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Previous state was: <State>
If sensor type is not discrete:
Current sensor value (in Amps): <Reading>
If sensor type is discrete:
Discrete current state: <State>
Warning
A current sensor on the power supply for the specified system exceeded its warning threshold. The sensor location, chassis location, previous state, and current sensor value are provided.
1204
Current sensor detected a failure value
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Previous state was: <State>
If sensor type is not discrete:
Current sensor value (in Amps): <Reading>
If sensor type is discrete:
Discrete current state: <State>
Error
A current sensor on the power supply for the specified system exceeded its failure threshold. The sensor location, chassis location, previous state, and current sensor value are provided.
1205
Current sensor detected a non-recoverable value
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Previous state was: <State>
If sensor type is not discrete:
Current sensor value (in Amps): <Reading>
If sensor type is discrete:
Discrete current state: <State>
Error
A current sensor in the specified system detected an error from which it cannot recover. The sensor location, chassis location, previous state, and current sensor value are provided.
Chassis Intrusion Messages
Chassis intrusion messages listed in Table 2-6 are a security measure. Chassis intrusion means that someone is opening the cover to a system's chassis. Alerts are sent to prevent unauthorized removal of parts from a chassis.
A chassis intrusion sensor in the specified system failed. The sensor location, chassis location, previous state, and chassis intrusion state are provided.
1251
Chassis intrusion sensor value unknown
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Previous state was: <State>
Chassis intrusion state: <Intrusion state>
Information
A chassis intrusion sensor in the specified system could not obtain a reading. The sensor location, chassis location, previous state, and chassis intrusion state are provided.
1252
Chassis intrusion returned to normal
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Previous state was: <State>
Chassis intrusion state: <Intrusion state>
Information
A chassis intrusion sensor in the specified system detected that a cover was opened while the system was operating but has since been replaced. The sensor location, chassis location, previous state, and chassis intrusion state are provided.
1253
Chassis intrusion in progress
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Previous state was: <State>
Chassis intrusion state: <Intrusion state>
Warning
A chassis intrusion sensor in the specified system detected that a system cover is currently being opened and the system is operating. The sensor location, chassis location, previous state, and chassis intrusion state are provided.
1254
Chassis intrusion detected
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Previous state was: <State>
Chassis intrusion state: <Intrusion state>
Error
A chassis intrusion sensor in the specified system detected that the system cover was opened while the system was operating. The sensor location, chassis location, previous state, and chassis intrusion state are provided.
1255
Chassis intrusion sensor detected a non-recoverable value
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Previous state was: <State>
Chassis intrusion state: <Intrusion state>
Error
A chassis intrusion sensor in the specified system detected an error from which it cannot recover. The sensor location, chassis location, previous state, and chassis intrusion state are provided.
Redundancy Unit Messages
Redundancy means that a system chassis has more than one of certain critical components. Fans and power supplies, for example, are so important for preventing damage or disruption of a computer system that a chassis may have "extra" fans or power supplies installed. Redundancy allows a second or nth fan to keep the chassis components at a safe temperature when the primary fan has failed. Redundancy is normal when the intended number of critical components are operating. Redundancy is degraded when a component fails but others are still operating. Redundancy is lost when the number of components functioning falls below the redundancy threshold.
Table 2-7 lists the redundancy unit messages.
The number of devices required for full redundancy is provided as part of the message, when applicable, for the redundancy unit and the platform. For details on redundancy computation, see the respective platform documentation.
A redundancy sensor in the specified system failed. The redundancy unit location, chassis location, previous redundancy state, and the number of devices required for full redundancy are provided.
1301
Redundancy sensor value unknown
Redundancy unit: <Redundancy location in chassis>
Chassis location: <Name of chassis>
Previous redundancy state was: <State>
Information
A redundancy sensor in the specified system could not obtain a reading. The redundancy unit location, chassis location, previous redundancy state, and the number of devices required for full redundancy are provided.
1302
Redundancy not applicable
Redundancy unit: <Redundancy location in chassis>
Chassis location: <Name of chassis>
Previous redundancy state was: <State>
Information
A redundancy sensor in the specified system detected that a unit was not redundant. The redundancy location, chassis location, previous redundancy state, and the number of devices required for full redundancy are provided.
1303
Redundancy is offline
Redundancy unit: <Redundancy location in chassis>
Chassis location: <Name of chassis>
Previous redundancy state was: <State>
Information
A redundancy sensor in the specified system detected that a redundant unit is offline. The redundancy unit location, chassis location, previous redundancy state, and the number of devices required for full redundancy are provided.
1304
Redundancy regained
Redundancy unit: <Redundancy location in chassis>
Chassis location: <Name of chassis>
Previous redundancy state was: <State>
Information
A redundancy sensor in the specified system detected that a "lost" redundancy device has been reconnected or replaced; full redundancy is in effect. The redundancy unit location, chassis location, previous redundancy state, and the number of devices required for full redundancy are provided.
1305
Redundancy degraded
Redundancy unit: <Redundancy location in chassis>
Chassis location: <Name of chassis>
Previous redundancy state was: <State>
Warning
A redundancy sensor in the specified system detected that one of the components of the redundancy unit has failed but the unit is still redundant. The redundancy unit location, chassis location, previous redundancy state, and the number of devices required for full redundancy are provided.
1306
Redundancy lost
Redundancy unit: <Redundancy location in chassis>
Chassis location: <Name of chassis>
Previous redundancy state was: <State>
Warning or Error (depending on the number of units that are functional)
A redundancy sensor in the specified system detected that one of the components in the redundant unit has been disconnected, has failed, or is not present. The redundancy unit location, chassis location, previous redundancy state, and the number of devices required for full redundancy are provided.
Power Supply Messages
Power supply sensors monitor how well a power supply is functioning. Power supply messages listed in
Table 2-8 provide status and warning information for power supplies present in a particular chassis.
Power supply sensor has failed Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Previous state was: <State>
Power Supply type: <type of power supply>
<Additional power supply status information>
If in configuration error state:
Configuration error type: <type of configuration error>
Information
A power supply sensor in the specified system failed. The sensor location, chassis location, previous state, and additional power supply status information are provided.
1351
Power supply sensor value unknown
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Previous state was: <State>
Power Supply type: <type of power supply>
<Additional power supply status information>
If in configuration error state:
Configuration error type: <type of configuration error>
Information
A power supply sensor in the specified system could not obtain a reading. The sensor location, chassis location, previous state, and additional power supply status information are provided.
1352
Power supply returned to normal Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Previous state was: <State>
Power Supply type: <type of power supply>
<Additional power supply status information>
If in configuration error state:
Configuration error type: <type of configuration error>
Information
A power supply has been reconnected or replaced. The sensor location, chassis location, previous state, and additional power supply status information are provided.
1353
Power supply detected a warning Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Previous state was: <State>
Power Supply type: <type of power supply>
<Additional power supply status information>
If in configuration error state:
Configuration error type: <type of configuration error>
Warning
A power supply sensor reading in the specified system exceeded a user-definable warning threshold. The sensor location, chassis location, previous state, and additional power supply status information are provided.
1354
Power supply detected a failure
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Previous state was: <State>
Power Supply type: <type of power supply>
<Additional power supply status information>
If in configuration error state:
Configuration error type: <type of configuration error>
Error
A power supply has been disconnected or has failed. The sensor location, chassis location, previous state, and additional power supply status information are provided.
1355
Power supply sensor detected a non-recoverable value
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Previous state was: <State>
Power Supply type: <type of power supply>
<Additional power supply status information>
If in configuration error state:
Configuration error type: <type of configuration error>
Error
A power supply sensor in the specified system detected an error from which it cannot recover. The sensor location, chassis location, previous state, and additional power supply status information are provided.
Memory Device Messages
Memory device messages listed in Table 2-9 provide status and warning information for memory modules present in a particular system. Memory devices determine health status by monitoring the ECC memory correction rate and the type of memory events that have occurred.
NOTE: A critical status does not always indicate a system failure or loss of data. In some instances, the system has exceeded the ECC correction rate. Although the system continues to function, you should perform system maintenance as described in Table 2-9.
NOTE: In Table 2-9, <status> can be either critical or non-critical.
Memory device status is <status> Memory device location: <location in chassis>
Possible memory module event cause: <list of causes>
Warning
A memory device correction rate exceeded an acceptable value. The memory device status and location are provided.
1404
Memory device status is <status> Memory device location: <location in chassis>
Possible memory module event cause: <list of causes>
Error
A memory device correction rate exceeded an acceptable value, a memory spare bank was activated, or a multibit ECC error occurred. The system continues to function normally (except for a multibit error). Replace the memory module identified in the message during the system's next scheduled maintenance. Clear the memory error on multibit ECC error. The memory device status and location are provided.
Fan Enclosure Messages
Some systems are equipped with a protective enclosure for fans. Fan enclosure messages listed in Table 2-10 monitor whether foreign objects are present in an enclosure and how long a fan enclosure is missing from a chassis.
The fan enclosure sensor in the specified system failed. The sensor location and chassis location are provided.
1451
Fan enclosure sensor value unknown
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Information
The fan enclosure sensor in the specified system could not obtain a reading. The sensor location and chassis location are provided.
1452
Fan enclosure inserted into system
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Information
A fan enclosure has been inserted into the specified system. The sensor location and chassis location are provided.
1453
Fan enclosure removed from system
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Warning
A fan enclosure has been removed from the specified system. The sensor location and chassis location are provided.
1454
Fan enclosure removed from system for an extended amount of time
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Error
A fan enclosure has been removed from the specified system for a user-definable length of time. The sensor location and chassis location are provided.
1455
Fan enclosure sensor detected a non-recoverable value
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Error
A fan enclosure sensor in the specified system detected an error from which it cannot recover. The sensor location and chassis location are provided.
AC Power Cord Messages
AC power cord messages listed in Table 2-11 provide status and warning information for power cords that are part of an AC power switch, if your system supports AC switching.
AC power cord sensor has failed Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Information
An AC power cord sensor in the specified system failed. The AC power cord status cannot be monitored. The sensor location and chassis location information are provided.
1501
AC power cord is not being monitored
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Information
The AC power cord status is not being monitored. This occurs when a system's expected AC power configuration is set to nonredundant. The sensor location and chassis location information are provided.
1502
AC power has been restored
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Information
An AC power cord that did not have AC power has had the power restored. The sensor location and chassis location information are provided.
1503
AC power has been lost
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Warning
An AC power cord has lost its power, but there is sufficient redundancy to classify this as a warning. The sensor location and chassis location information are provided.
1504
AC power has been lost
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Error
An AC power cord has lost its power, and lack of redundancy requires this to be classified as an error. The sensor location and chassis location information are provided.
1505
AC power has been lost
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Error
An AC power cord sensor in the specified system failed. The AC power cord status cannot be monitored. The sensor location and chassis location information are provided.
Hardware Log Sensor Messages
Hardware logs provide hardware status messages to systems management software. On certain systems, the hardware log is implemented as a circular queue. When the log becomes full, the oldest status messages are overwritten when new status messages are logged. On some systems, the log is not circular. On these systems, when the log becomes full, subsequent hardware status messages are lost. Hardware log sensor messages listed in Table 2-12 provide status and warning information about the noncircular logs that may fill up, resulting in lost status messages.
A hardware log sensor in the specified system is disabled. The log type information is provided.
1551
Log status is unknown
Log type: <Log type>
Information
A hardware log sensor in the specified system could not obtain a reading. The log type information is provided.
1552
Log size is no longer near or at capacity
Log type: <Log type>
Information
The hardware log on the specified system is no longer near or at its capacity, usually as the result of clearing the log. The log type information is provided.
1553
Log size is near or at capacity
Log type: <Log type>
Warning
The size of a hardware log on the specified system is near or at the capacity of the hardware log. The log type information is provided.
1554
Log size is full
Log type: <Log type>
Error
The size of a hardware log on the specified system is full. The log type information is provided.
1555
Log sensor has failed
Log type: <Log type>
Error
A hardware log sensor in the specified system failed. The hardware log status cannot be monitored. The log type information is provided.
Processor Sensor Messages
Processor sensors monitor how well a processor is functioning. Processor messages listed in
Table 2-13 provide status and warning information for processors in a particular chassis.
A processor sensor in the specified system is not functioning. The sensor location, chassis location, previous state and processor sensor status are provided.
1601
Processor sensor value unknown Sensor Location: <Location in chassis>
Chassis Location: <Name of chassis>
Previous state was: <State>
Processor sensor status: <status>
Information
A processor sensor in the specified system could not obtain a reading. The sensor location, chassis location, previous state and processor sensor status are provided.
1602
Processor sensor returned to a normal value
Sensor Location: <Location in chassis>
Chassis Location: <Name of chassis>
Previous state was: <State>
Processor sensor status: <status>
Information
A processor sensor in the specified system transitioned back to a normal state. The sensor location, chassis location, previous state and processor sensor status are provided.
1603
Processor sensor detected a warning value
Sensor Location: <Location in chassis>
Chassis Location: <Name of chassis>
Previous state was: <State>
Processor sensor status: <status>
Warning
A processor sensor in the specified system is in a throttled state. The sensor location, chassis location, previous state and processor sensor status are provided.
1604
Processor sensor detected a failure value
Sensor Location: <Location in chassis>
Chassis Location: <Name of chassis>
Previous state was: <State>
Processor sensor status: <status>
Error
A processor sensor in the specified system is disabled, has a configuration error, or experienced a thermal trip. The sensor location, chassis location, previous state and processor sensor status are provided.
1605
Processor sensor detected a non-recoverable value
Sensor Location: <Location in chassis>
Chassis Location: <Name of chassis>
Previous state was: <State>
Processor sensor status: <status>
Error
A processor sensor in the specified system has failed. The sensor location, chassis location, previous state and processor sensor status are provided.
Pluggable Device Messages
The pluggable device messages listed in Table 2-14 provide status and error information when some devices, such as memory cards, are added or removed.
Table 2-14. Pluggable Device Messages
Event ID
Description
Severity
Cause
1650
<Device plug event type unknown>
Device location: <Location in chassis, if available>
Chassis location: <Name of chassis, if available>
Additional details: <Additional details for the events, if available>
Information
A pluggable device event message of unknown type was received. The device location, chassis location, and additional event details, if available, are provided.
1651
Device added to system
Device location: <Location in chassis>
Chassis location: <Name of chassis>
Additional details: <Additional details for the events>
Information
A device was added in the specified system. The device location, chassis location, and additional event details, if available, are provided.
1652
Device removed from system
Device location: <Location in chassis>
Chassis location: <Name of chassis>
Additional details: <Additional details for the events>
Information
A device was removed from the specified system. The device location, chassis location, and additional event details, if available, are provided.
1653
Device configuration error detected
Device location: <Location in chassis>
Chassis location: <Name of chassis>
Additional details: <Additional details for the events>
Error
A configuration error was detected for a pluggable device in the specified system. The device may have been added to the system incorrectly.
Battery Sensor Messages
Battery sensors monitor how well a battery is functioning. Battery messages listed in Table 2-15 provide status and warning information for batteries in a particular chassis.
Table 2-15. Battery Sensor Messages
Event ID
Description
Severity
Cause
1700
Battery sensor has failed
Sensor location: <Location in chassis>
Chassis location: <Name of chassis>
Previous state was: <State>
Battery sensor status: <status>
Information
A battery sensor in the specified system is not functioning. The sensor location, chassis location, previous state, and battery sensor status are provided.
1701
Battery sensor value unknown
Sensor Location: <Location in chassis>
Chassis Location: <Name of chassis>
Previous state was: <State>
Battery sensor status: <status>
Information
A battery sensor in the specified system could not retrieve a reading. The sensor location, chassis location, previous state, and battery sensor status are provided.
1702
Battery sensor returned to a normal value
Sensor Location: <Location in chassis>
Chassis Location: <Name of chassis>
Previous state was: <State>
Battery sensor status: <status>
Information
A battery sensor in the specified system detected that a battery transitioned back to a normal state. The sensor location, chassis location, previous state, and battery sensor status are provided.
1703
Battery sensor detected a warning value
Sensor Location: <Location in chassis>
Chassis Location: <Name of chassis>
Previous state was: <State>
Battery sensor status: <status>
Warning
A battery sensor in the specified system detected that a battery is in a predictive failure state. The sensor location, chassis location, previous state, and battery sensor status are provided.
1704
Battery sensor detected a failure value
Sensor Location: <Location in chassis>
Chassis Location: <Name of chassis>
Previous state was: <State>
Battery sensor status: <status>
Error
A battery sensor in the specified system detected that a battery has failed. The sensor location, chassis location, previous state, and battery sensor status are provided.
1705
Battery sensor detected a non-recoverable value
Sensor Location: <Location in chassis>
Chassis Location: <Name of chassis>
Previous state was: <State>
Battery sensor status: <status>
Error
A battery sensor in the specified system detected that a battery has failed. The sensor location, chassis location, previous state, and battery sensor status are provided.
