After completing the hardware installation procedures in the previous section, you must install and configure the DRAC III software. This section provides information on installing and configuring the DRAC III software. For more information on the DRAC III software components, see "Software Components."
If you are adding the DRAC III to an existing managed system, it is recommended that you update the system's BIOS before installing the DRAC III to ensure full support for the card. In addition, if your managed system is running a 32-bit operating system, you must add and configure the SNMP service before installing the software on the managed system. The following sections provide procedures for updating the BIOS, and for adding and configuring the SNMP service.
The SNMP service allows the managed system's software to communicate with the DRAC III. If the operating system on the DRAC III managed system was installed using the Dell OpenManage Server Assistant CD (or System Support CD for 64-bit systems), the SNMP service may already be configured. However, if it is not, you must add and configure the SNMP service before installing the DRAC III software on the managed system.
NOTE: If you add the SNMP service after you apply the Microsoft service pack, you must
reinstall the current service pack and possibly the appropriate video drivers.
Reboot the system and log on as the administrator.
NOTE: Whenever you are required to log on to the system (for instance, after shutdown), ensure
that you log on as the administrator; otherwise, you may not have permission to perform all the
required procedures.
Click the Start button, and point to Settings—> Control Panel.
In the Control Panel window,double-click the Network icon.
Click Services.
Double-click SNMP Service.
Click the Traps tab.
Enter public in the Community Name field.
This field is case-sensitive.
Click Add to the right of the Community Name field.
Click Add under the Trap Destinations field.
Enter the IP address of the management station(s) on your network in dotted-decimal
notation as in the following example:
143.166.187.3
NOTE: Leave this item blank if no management station is present.
Click the Start button, point to Settings, and then point to Control Panel.
Double-click Administrative Tools.
Double-click Computer Management.
In the console tree, click Services.
In the details pane, click SNMP Service.
On the Action menu, click Properties.
On the Traps tab, under Community name, type the case-sensitive community name
to which the managed system will send trap messages, and then click Add to list.
In Trap destinations, click Add.
In the Host name, IP, or IPX address fields, type the required information for the
managed system, and click Add.
Repeat steps 7 through 9 until you have added all the communities and trap
destinations you want.
NOTE: The SNMP service does not need to be restarted for your settings to take effect. If
you change existing SNMP settings, your changes take effect immediately.
Confirm that the bindery context is set on the system by typing config at the system
console.
A tree name and bindery context appear.
NOTE: If no bindery context is set, the Dell OpenManage™ Server Administrator log in fails. To
determine if the bindery context is set, check the Security tab. If the bindery context is not set,
the tab is empty.
Configure SNMP with proper community names by loading inetcfg.
If SNMP is not properly configured, you cannot log in successfully and configure the DRAC III.
The following is a sample SNMP Config line contained in netinfo.cfg:
Adding the SNMP Service for a Red Hat Linux 7.1 or Later Managed System
Before installing the DRAC III software on a Red Hat Linux 7.1 or later managed system, you must first install the ucd-snmp package using the following command:
The following provides a high-level overview of the DRAC III software installation and configuration process. Some steps give you the option of using several different tools to perform the configuration, including Server Administrator, IT Assistant, and the racadm utility. Those procedures that can be performed using your operating system utilities are included in this section.
NOTE: For more information about the DRAC III software components, see "Software
Components."
Depending on the tool used to perform the configuration, you will need to reference the following documents for more information:
Server Administrator – see your Dell OpenManage Server Administrator User's Guide.
IT Assistant – see your Dell OpenManage IT Assistant User's Guide.
Install the software on the managed system using the Systems Management CD (32-bit
systems) or the Server Management CD (64-bit systems). For instructions on installing
this software, see your Dell OpenManage Server Administrator User's Guide.
The managed system has the following components installed: a DRAC III, the appropriate version of Server Administrator, and the DRAC III agent. Depending on the operating system, the DRAC III agent consists of either Windows services, Novell NLMs, or Red Hat Linux drivers and daemons. The DRAC III agent automatically starts when you boot the managed system.
NOTE: If it becomes necessary to reinstall or upgrade the Server Administrator on the
managed system, you must first uninstall the DRAC III software on the managed system.
This software uses a library file provided by the Server Administrator. If you reinstall
Server Administrator and the DRAC III is using the library file, the installation may fail.
If necessary, install (or upgrade) the software on the management station, including
Server Administrator and Dell OpenManage IT Assistant, using the Systems
Management CD (32-bit systems) or the Server Management CD (64-bit systems). For
instructions on installing this software, see your Dell OpenManage Server
Administrator User's Guide.
A management station is a system (typically a workstation running Windows NT or Windows 2000) that has the following components installed: appropriate versions of Server Administrator (or IT Assistant), a supported browser (Internet Explorer 5.x, Netscape Navigator 6.x or later), Windows services (if applicable), Dell services, and user interface elements.
It is possible to configure and manage the DRAC III using IT Assistant. To do so, you must have IT Assistant version 6.1 or later installed.
NOTE: While the configuration procedures in the Dell OpenManage IT Assistant User's
Guide reference only the Dell OpenManage Remote Assistant Card II (DRAC II) and the
Dell OpenManage Remote Service Card (DRSC), the procedures are also valid for DRAC III
configuration.
If the DRAC III PPP connection was not automatically added when the managed
system software was installed on your Windows NT managed system, you must add
this connection manually. For instructions, see "Adding a PPP Connection on a
Windows NT Managed System."
NOTE: This step applies only to Windows-NT managed systems.
Add and configure the remote access service on the management station using one of
the following tools:
If connecting to the DRAC III Web-based interface from a client system which
connects to the Internet through a proxy server, configure the Web browser to connect
properly to the Web-based interface. See "Configuring a Web Browser to Access the
Web-Based Interface."
When the Windows NT managed system software is installed, a PPP connection for the DRAC III is automatically added. In the event the modem is not added during the installation, perform the following steps:
Click the Start button, point to Settings, and click Control Panel.
Double-click the Modems icon.
Click Add to add a new modem.
The Install New Modem wizard dialog box displays.
Select Don't detect my modem; I will select it from a list, and then click Next.
Select RAC PPP Connection Using RACPORT from the list of available modems,
andthen click Next.
Select RACPORT from the list of available serial ports, and then click Next.
The new modem should appear in the modem installation wizard list.
Click Finish.
The following message is displayed:
Dial-Up Networking needs to be configured because the list of installed modems has changed. Would you like to do this now?
After installing the software on the managed system and the management station, you must set up the remote access service (RAS). If you are using Server Administrator to configure your DRAC III, see your Dell OpenManage Server Administrator User's Guide for instructions. If you are using IT Assistant, see your Dell OpenManage IT Assistant User's Guide. If you are using the racadm utility, see "racadm Utility." Otherwise, use the procedures in the following sections for remote access service setup.
Click the Start button, point to Settings, and click Control Panel.
Double-click the Network icon and click the Services tab.
Select Remote Access Service and click Properties (if Remote Access Service is not
listed, add it to the list using the Add button, and then return to this step).
In the Remote Access Setup dialog box, select RACPORT from the list of ports (if
necessary, add an available modem), and click Configure.
At the Configure Port Usage dialog box, click Dial out only, and then click OK.
From the Remote Access Setup dialog box, click Continue.
Windows NT installs all of the neccessary files. When prompted, reboot the system.
Click the Start button, point to Settings, and click Control Panel.
Double-click the Network icon and click the Services tab.
Select Remote Access Service and click Properties (if Remote Access Service is not
listed, add it to the list using the Add button, and then return to this step).
In the Remote Access Setup dialog box, select a port entry from the list (if necessary,
add an available modem), and click Configure.
At the Configure Port Usage dialog box, click Dial and Receive Calls, and then click
OK.
At the Remote Access Setup dialog box, click Network.
At the Network Configuration dialog box, perform the following steps:
Under Dial-out Protocols, select the TCP/IP check box only.
Under Allow Remote Clients Running, select the TCP/IP check box only.
Under Encryption Settings, select the Allow Any Authentication Including Clear
Text check box. Do not select the Enable Multilink check box.
Click Configure.
At the RAS Server TCP/IP Configuration dialog box, perform the following steps:
Under Allow Remote TCP/IP Clients to Access, select Entire Network or This
Computer Only, depending on the level of security required.
Select Use DHCP to Assign Remote TCP/IP Client Addresses or Use Static
Address Port (including the appropriate port number), depending on the level of
security required. Do not select the Allow Remote Clients to Request a
Predetermined IP Address check box.
Click OK.
At the Network Config dialog box, click OK.
At the Remote Access Setup dialog box, click Continue.
Click Close.
RAS Setup for Windows 2000 Management Stations
Right-click My Computer.
Click Manage.
Double-click Services and Applications.
Double-click Services.
If the Startup Type column for Routing and Remote Access is not set to Automatic,
right click Routing and Remote Access.
Click Properties.
In the Routing and Remote Access (Local Computer) dialog box, click the down
arrow on the Startup Type pull-down menu.
Click Automatic.
Click Apply.
Click OK.
If the Status column for Routing and Remote Access does not show Started,
right-click Routing and Remote Access and click Start.
The Routing and Remote Access service should start automatically on subsequent restarts of the management station.
If you want to use the modem on your management station to dial-up the DRAC III, you must first configure the management station's modem. The following sections provide instructions for configuring the modem on Windows NT and Windows 2000 management stations.
Click the Start button, point to Settings, point to Control Panel, and click Phone and
Modem Options.
In the Phone and Modem Options dialog box, click the Modems tab, and click Add.
Follow the instructions in the Add/Remove Hardware Wizard.
Repeat steps 2 and 3 for each modem you want to install.
To configure a dial-up connection, click the Start button, point to Settings—>
Control Panel—> Network and Dial-up Connections, and click Make new
connection.
Follow the instructions in the Network Connection wizard.
For security purposes, the DRAC III supports two types of users: DRAC III users and DRAC III dial-in users. Additionally, demand dial-out entries are configured with management station user information.
DRAC III users – DRAC III users can establish console redirection and perform configuration and management actions on the DRAC III.
DRAC III dial-in users – Also called Point-to-point protocol (PPP) users, dial-in user names and passwords are used to establish a dial-in connection only. After the connection is established, a DRAC III user name and password must be supplied in order to perform console redirection, configuration, and management actions.
Demand dial-out entries – Demand dial-out entries specify a destination IP address, the telephone number of a management station, a management station user name and password, and the authentication type associated with the management station user name and password.
NOTE: The entries are not DRAC III users. Rather, they are remote management station
users.
NOTE: It is not necessary for the destination IP address to be the remote management
station. The destination IP address may be the IP address of another remote management
station. If the destination IP address is the IP address of another remote management
station, the management station answering the telephone must be able to route to the
destination IP address specified.
Some of the DRAC III features are configured within the context of a DRAC III user, such as alerting and paging. The following sections describe how to configure the DRAC III features and/or users outside the Server Administrator/IT Assistant environment.
To provide client access to the managed system's DRAC III, you must add and configure dial-in (PPP) users. For information on configuring these features using Server Administrator, see your Dell OpenManage Server Administrator User's Guide. For information on configuring these features using IT Assistant, see your Dell OpenManage IT Assistant User's Guide. For information on configuring these features using the racadm utility, see "racadm Utility." Otherwise, use the procedures in the following sections to add and configure dial-in users.
NOTE: If for any reason all the DRAC III users are deleted, use the racadm utility to create new
users.
If a dial-in client with a Microsoft operating system has a NIC IP address on the same subnetwork as the DRAC III PPP dial-in addresses (whether by DHCP, static configuration, or default configuration), the dial-in network connections between the client NIC address and the DRAC III NIC address operate in an unexpected manner, or do not operate at all. This behavior is limited to network connections initiated by a Microsoft client to the DRAC III local dial-in IP address.
NOTE: The DRAC III Managed Node PPP Server uses the 192.168.0.0 network to
communicate with the installed DRAC III.
Specifically, if you want to dial into a DRAC III from a Microsoft client, you must ensure that:
If using DRAC III static configuration, configure the DRAC III dial-in base address to be on a different subnetwork from the client NIC.
If using DHCP, ensure that the DHCP server does not assign the client NIC and DRAC III dial-in addresses on the same subnetwork.
If using the DRAC III autogenerated address, ensure that the client NIC is not on the 10.0.0.0 private internetwork.
For instructions on changing the PPP server IP address on the managed system, see the following section.
Click the Start button, point to Settings, and click Control Panel.
Click the Add/Remove Programs icon.
In the Add/Remove Programs Properties dialog box, click the Windows Setup tab,
select Communications in the list, and then click Details.
In the Communications dialog box, ensure that Dial-Up Networking and Phone
Dialer are selected (checked). If not, install these components.
It may be necessary to download msdun13.exe from the Microsoft website for Windows 95; this file contains patches that enhance dial-up networking.
Return to the Control Panel and click the Network icon.
On the Configuration tab, ensure that Client for Microsoft Networks, Dial-Up
Adapter, and TCP/IP are installed. If not, install the components by performing one
or both of the following:
If Dial-Up Adapter is missing, click Add; next, in the Select Network Component
Type dialog box, click Adapter.
If TCP/IP is missing, click Add; next, in the Select Network Component Type
dialog box, click Protocol.
In the Network dialog box, select TCP/IP—> Dial-Up Adapter, and then click
Properties.
The properties in the TCP/IP Properties dialog box must remain at their defaults. Confirm the following settings:
On the IP Address tab, ensure that Obtain an IP Address Automatically is
selected.
On the WINS Resolution tab, ensure that Disable WINS Resolution is selected.
On the Gateway tab, ensure that New gateway is blank.
In the TCP/IP Properties dialog box, click OK.
In the Network dialog box, click OK.
Close the Control Panel window.
Click the Start button, point to Programs, point to Accessories, and click Dial-Up
Networking.
In the Dial-Up Networking dialog box, click Make New Connection and type in the
modem, name of the DRAC III, and telephone number of the DRAC III.
After you make the new connection, right-click on the connection and click
Properties.
Click the Server Types tab, and ensure that only TCP/IP is selected (checked).
Click TCP/IP Settings and ensure that only Server Assigned IP address, Server
Assigned Name Server Addresses, and Use IP Header Compression are selected
(checked).
NOTE: The following instructions vary slightly depending on the system's Windows NT
configuration. You may be prompted for your Microsoft Windows NT Operating System CD
while performing some of these procedures.
Verify that the system has Service Pack 5 (SP5) or later installed.
Click the Start button, point to Settings, and click Control Panel.
Click the Network icon.
In the Network dialog box, click the Services tab.
Click Add.
In the Select Network Service dialog box, select Remote Access Service.
Click OK.
You may be prompted for your Microsoft Windows NT Operating System CD.
In the Remote Access Setup dialog box, click Add.
In the Add RAS Device dialog box, click Install Modem.
Select (check) the box next to the modem you want to install.
Insert your modem driver diskette or point to the directory where your modem driver
software resides.
After installing your first modem, click Add for each modem you want to install.
In the Remote Access Setup dialog box, select each modem and click Configure.
Select Dial out and receive calls.
Click Network in Network Configuration.
Ensure that TCP/IP protocol is selected.
In Server Settings, select TCP/IP and click Configure.
If a check box named Use Gateway on the Remote Network is present, deselect
(uncheck) it.
In the RAS Server TCP/IP Configuration, select DHCP.
Select the option to allow remote clients to request an IP address.
NOTE: The following instructions vary slightly depending on the system's Windows 2000
configuration.
Click the Start button, point to Settings—> Control Panel—> Network and Dialup
Connections, and click Make New Connection.
Click Next.
Select Dial-Up to a private network.
Click Next.
Enter the telephone number of the DRAC III to which you want to connect.
Click Next three times.
Type a name for this connection.
Click Finish.
Click the Start button, point to Settings—> Control Panel—> Network and Dialup
Connections, right-click the connection you just created and named, and select
Properties.
Click the Networking tab.
Ensure that Type of dial-up server I am calling is set to PPP: Windows
95/98/NT4/2000, Internet.
Ensure that Internet Protocol (TCP/IP) is selected (checked).
Click Properties.
Click Advanced.
Deselect (uncheck) Use default gateway on remote network.
Click OK twice.
Click the Security tab.
Ensure that Allow Unsecured Password is selected (different service pack versions of
Windows 2000 may move this option around, refer to it as Clear Text, or present it as
a check box; ensure that you find this option and select it).
NOTICE: Before beginning this procedure, PPP must first be configured and installed on the
client system. PPP-2.3 or later is available on the Internet at www.redhat.com.
Download and configure the latest PPP (2.3.11 or later) source code.
Read the readme.cbcp file included in the PPP software distribution.
Apply the patch included in the readme.cbcp file, and then make and install as usual.
To test whether your PPP daemon supports the callback protocol, open a command
shell and issue the following command:
pppd callback 1111
If your PPP daemon is not properly configured, it generates an error message about the callback option.
After verifying that your PPP daemon is configured with callback support, you must
set up the proper chat scripts for your environment.
An example modem setup is described at www-cache.mppmu.mpg.de/callback/linuxanalog.html.
Create the file /etc/ppp/peers/rac with the following contents:
tty02 crtcts 38400
connect `chat –v –f /etc/ppp/chat/rac'
noipdefault
nodefaultroute
lock
user <username>
remotename <rac>
where <username> is the DRAC III user name that is supplied to the DRAC III, and <rac> is the name preferred for the DRAC III.
Create the file /etc/ppp/chat/rac with the following contents, where the actual
telephone number replaces 555-1212.
This chat script assumes a modem with a standard AT command set and may need to be modified if the actual modem does not support this command set:
ABORT "NO CARRIER"
ABORT "NO DIALTONE"
ABORT "ERROR"
ABORT "NO ANSWER"
ABORT "BUSY"
"" "at"
OK "at&d2&d1"
OK "atdt555-1212"
Edit the /etc/ppp/chap-secrets file (which lists PPP users and passwords) to include
the DRAC III PPP user.
Using the following example as a guideline, add a single line to the file.
NOTE: The <username> and <rac> values in the following example must match the
<username> and <rac> values placed in the /etc/ppp/peers/rac file in the previous
step.
# client server secret IP addresses
<username> <rac> <password> *
where <password> is the password that is supplied to the DRAC III during the authentication phase of PPP negotiation.
NOTE: The IP address value (indicated by the * symbol in the previous example) is not
used when acting as a PPP client.
For DRAC III dial-out alert notifications, a single SMTP server may be specified for e-mail reception, with up to eight SNMP trap daemon destinations that can be specified. If the IP address of the SMTP server, or any of the SNMP trap daemon addresses, is specified in a demand dial-out entry, the DRAC III dials the telephone number specified in the demand dial-out entry to deliver an e-mail or SNMP trap to that address. Otherwise, if the IP address of the SMTP server, or any of the SNMP trap daemon addresses is not specified in a demand dial-out entry, the out-of-band DRAC III NIC is used to deliver the e-mail or SNMP trap to that address.
To support the dial-out notification feature on the DRAC III, the management station must allow for remote access (dial-in). See the following sections for instructions on configuring dial-out alert notifications.
To configure your Windows NT management station so that the DRAC III can establish a connection and log an alert, perform the fol-lowing steps:
At the management station, click the Start button, point to Programs—>
Administrative Tools, and then click User Manager.
From the User menu, select New User.
At the New User window, type the requested information in the Username, Password,
and Confirm Password fields.
NOTE: The user name and password specified here must be the same as the user name and
password on the management station.
Select the Password Never Expires check box, and then click Dialin.
At the Dial-in Information window, select the Grant Dial-in Permission To User
check box, and click No Call Back.
Click OK.
At the New User window, click Groups.
At the Group Memberships window, select the appropriate group for the user from
the window on the right side of the screen, and move the group to the left window.
You can control access permissions for each group.
To configure your Windows 2000 management station so that the DRAC III can establish a connection and log an alert, you must add a new local user. If the system is part of a domain, performing the procedure to add a user gives an existing domain user permission to use the system.
To add a new local user, perform the fol-lowing steps:
At the management station, click the Start button, point to Settings—> Control
Panel—>Users and Passwords.
NOTE: You must be logged on as an admistrator to access this setting.
From the Users and Passwords window, click the Advanced tab, and then click
Advanced.
Under Local Users and Groups, click Users, and then click Action.
Click New User.
In the New User window, type in a Username, Password, and Confirm Password.
Make sure the User must change password at next login check box is not selected.
The DRAC III contains an integrated 10Base-T or 100Base-T Ethernet NIC and supports TCP/IP. The NIC has a default address of 192.168.20.1 and a default gateway of 192.168.20.1.
It is possible to configure a limited number of DRAC III network settings using the DRAC III Option ROM utility.
To access the Option ROM utility, press <Ctrl><D> during the managed system's boot within 5 seconds of the time the DRAC III banner, firmware version, and current NIC IP address are displayed. The Dell Remote Access Card III Setup screen appears. Below the screen title is the Network Interface Properties menu.
This menu enables you to use a set of one-key-stroke menu options to select and change various parameters in the DRAC III NIC properties. The menu selections are not case sensitive.
The following is a list of the available option categories available through the Option ROM utility, including the options within each category.
NOTE: When modifying any of the following options, you can use the <Esc> key while entering
the value to avoid modifying the current value. If you press <option edit> and it toggles a
setting (changes the setting between two and only two possible values), press that key again to
change the value back to the original. <Esc> cannot undo a modification after a new value has
been entered. <Esc> has no effect on toggle options.
NIC TCP/IP Settings – Displays the current IP-Address, Netmask, and Gateway assigned to the DRAC III.
NOTE: If DHCP is enabled on the card and something is wrong with the DHCP system, the
category displays Unavailable for each option, and the following message blinks below the
option labels:
Waiting for response from DHCP Server
NIC TCP/IP Configuration Options
NOTE: If the DRAC III is configured to the same IP address as another NIC on the same
network, an IP address conflict occurs. The DRAC III stops responding to network
commands until the IP address is changed on the DRAC III. If the IP address conflict is
resolved by changing the address of the other NIC, the DRAC III must be reset.
Use DHCP is – Indicates whether the DHCP system has assigned the DRAC III IP address or whether the DRAC III is using a preset static IP address. The available settings are Enabled or Disabled. Press <D> to toggle the setting. When enabled, the three remaining options in this group are "dimmed-out" and do not display prominently. If disabled, the remaining options display at normal brightness.
Static IP-Addr – Indicates the preset static IP address that the DRAC III uses if DHCP is disabled. The default is 192.168.20.1. Press <I> to change this address.
Static Netmask – Indicates the preset static masked IP address of the DRAC III if DHCP is disabled. The default is 255.255.255.0. Press <N> to change this mask.
Static Gateway – Indicates the preset static gateway (router or switch address) of the DRAC III address if DHCP is disabled. The default is 192.168.20.1. Press <G> to change the address.
Ethernet Configuration Options
NIC is – Indicates whether the DRAC III NIC is Enabled or Disabled. Press <E> to toggle the setting. When enabled, the DRAC III NIC can be used for out-of-band access. You must enable this option to configure any of the remaining options on this screen. When disabled, all other options are "dimmed-out" and do not display prominently. If enabled, most or all of the remaining options display at normal brightness, depending upon the Use DHCP is setting.
Auto Negotiate – Indicates whether the DRAC III automatically configures LAN speed and duplex settings. The available settings are Enabled and Disabled. If not enabled, the user settings are used. Press <A> to toggle to this setting.
LAN Speed Setting – Indicates the speed at which the DRAC III NIC is set to communicate. The available settings are 10 Base-T and 100 Base-T. 10 Base-T represents a communication speed of 10 Mb per second. 100 Base-T represents a speed of 100 Mb per second. Press <S> to toggle this setting. This option is "dimmed-out" when Auto Negotiate is enabled.
LAN Duplex Setting – Indicates the duplex setting of the DRAC III NIC. The available settings are Half Duplex and Full Duplex. When set to Half Duplex, the NIC communicates in one direction at a time, indicating that at any given moment it can either receive or transmit information, but not both. When set to Full Duplex, the NIC communicates in both directions simultaneously. Press <X> to toggle to this setting. This option is "dimmed-out" when Auto Negotiate is enabled.
After you have made the changes you want, you can press <R> to save the changes and reboot the DRAC III, or you can press <Esc> to cancel all changes and exit the setup menu. If you decide to save your changes, the following message appears:
IMPORTANT: In order for your changes to take effect, they need to
be saved and the card needs to be reset. That should take about 25
seconds. Your computer will then continue booting normally.
Would you like to save the changes and reset the card now (<Y> or
<N>)?
Press <Y> to save the changes or <N> to return to the setup menu.
If connecting to the DRAC III Web-based interface from a client system which connects to the Internet through a proxy server, you need to configure the Web browser to connect properly to the Web-based interface. The following sections provide configuration instructions for both browsers supported by the DRAC III: Microsoft Internet Explorer 5.x or later, and Netscape Navigator 6.x or later.
The following list describes basic software information for DRAC III with Red Hat Linux:
To verify that the DRAC III driver is loaded, type the following command:
service racser status
To verify that the DRAC III event server for the managed system is loaded, type the following command:
service racsrvc status
To start, stop, get status of, load, or unload the racser service, type the following command:
service racser <action>
where <action> is start, stop, status, load, or unload.
For additional information on one of the three DRAC III services, type the following command:
man <service>
where <service> is racser, racvnc, or racsrvc.
NOTE: All three services (racser, racsrvc, and racvnc) start automatically when they are
installed and when the system is booted. These services stop automatically when they are
uninstalled or when the system is shut down.
To determine which version of a particular RPM package you have installed, use a package management tool such as GnoRPM, or use the RPM query command (rpm -q). For example:
rpm -q <package_name>
To determine which files were installed and where they are located, type the following command:
DRAC III is supported on precompiled kernels that are a part of the Red Hat Linux 7.1 or later distribution. DRAC III is not supported on recompiled kernels with other configuration options (for example, kernels configured for performance-tuning purposes).
NOTICE: Red Hat Linux may fail to load when started on recompiled kernels. If this situation
occurs, you must either restore the kernel and modules from backup, or you must reinstall the
kernel from the Red Hat RPM packages.
