Manuals

Manuals
System Management: Dell PowerConnect 3324/3348 Switch CLI Guide

Back to Contents Page

System Management

Dell™ PowerConnect™ 3324/3348 Switch CLI Guide

  ping

  reload

  clock set

  hostname

  asset-tag

  stack order

  show users

  show clock

  show system

  show version

  show system id



ping

Use the ping user EXEC command to send ICMP echo request packets to another node on the network.

Syntax

ping host [size packet_size] [count packet_count] [timeout time_out]

    • host—IP address being contacted.

    • packet_size—Number of bytes in a packet, from 56 to 1472 bytes. The actual packet size is eight bytes larger than the size specified because the switch adds header information.

    • packet_count—Number of packets to send, from 1 to 65535 packets. If 0 is entered it pings until stopped.

    • time_out—Timeout in milliseconds to wait for each reply, from 1 to 65535 milliseconds.

Default Configuration

The default packet size is 56 bytes.

The default packet count is 4 packets.

The default time-out is 1000 milliseconds.

Command Mode

User EXEC Mode

User Guidelines

Press ESC to stop pinging. Following are sample results of the ping command:

    • Destination does not respond—If the host does not respond, no answer from host appears in ten seconds.

    • Destination unreachable—The gateway for this destination indicates that the destination is unreachable.

    • Network or host unreachable—The switch found no corresponding entry in the route table.

Examples

The following example displays a ping to IP address 10.1.1.1.

Console> ping 10.1.1.1

64 bytes from 10.1.1.1: icmp_seq=0. time=11 ms

64 bytes from 10.1.1.1: icmp_seq=1. time=8 ms

64 bytes from 10.1.1.1: icmp_seq=2. time=8 ms

64 bytes from 10.1.1.1: icmp_seq=3. time=7 ms

64 bytes from 10.1.1.1: icmp_seq=4. time=11 ms

64 bytes from 10.1.1.1: icmp_seq=5. time=7 ms

64 bytes from 10.1.1.1: icmp_seq=6. time=7 ms

^C

----10.1.1.1 PING Statistics----

7 packets transmitted, 7 packets received, 0% packet loss

round-trip (ms) min/avg/max = 7/8/11

Console>


reload

Use the reload user EXEC command to reload the operating system.

Syntax

reload

Default Configuration

This command has no default configuration.

Command Mode

Privileged EXEC Mode

User Guidelines

There are no user guidelines for this command.

Examples

The following example displays the prompt when entering the reload command.

Console >reload

This command will reset the whole system and disconnect your telnet session.

Do you want to continue (y/n) [n]?


clock set

Use the clock set user EXEC command to manually set the system clock.

Syntax

clock set hh:mm:ss day month year

or

clock set hh:mm:ss month day year

    • hh:mm:ss—Current time in hours (military format), minutes, and seconds (0-23, mm: 0-59, ss: 0-59).

    • day—Current day (by date) in the month (1-31).

    • month—Current month using the first three letters by name (Jan, ... Dec).

    • year—Current year (1998-2097).

Default Configuration

This command has no default configuration.

Command Mode

User EXEC Mode

User Guidelines

This device clock is not a Real Time Clock (RTC). When the device is rebooted or restarted, the clock setting is deleted.

Examples

The following example sets the system time.

Console> clock set 13:32:00 7 Mar 2002


hostname

Use the hostname global configuration command to specify or modify the device host name. To restore the default host name, use the no form of the command.

Syntax

hostname name

no hostname

    • name—The name of this host.

Default Configuration

This command has no default configuration.

Command Mode

Global Configuration Mode

User Guidelines

There are no user guidelines for this command.

Examples

The following example specifies dell as the device host name.

Console (config)# hostname dell


asset-tag

Use the asset-tag global configuration command to specify the device asset-tag. Use the no form of this command to restore the default host name.

Syntax

asset-tag [unit unit] tag

no asset-tag [unit unit]

    • unit unit—Unit number. If unspecified defaults to the master unit number.

    • tag—The device asset-tag.

Default Configuration

This command has no default configuration.

Command Mode

Global Configuration Mode

User Guidelines

There are no user guidelines for this command.

Examples

The following example specifies the device asset tag.

Console (config)# asset-tag 45456


stack order

Use the stack order global configuration command to configure the unit physical order in the stack. To return to the default value, use the no form of this command.

Syntax

stack order order1 order2 {order3 ...}

no stack order

    • order1 order2 {order3 ...}—Unit order. All the units in the stack are configured in the same command.

Default Configuration

The default value is the unit number.

Command Mode

Global Configuration Mode

User Guidelines

There are no user guidelines for this command.

Examples

The following example configures the device 2 as the first unit and device 1 as the second unit in the stack.

Console (config)# stack order 2 1


show users

Use the show users user EXEC command to display information about the active users.

Syntax

show users

Default Configuration

This command has no default configuration.

Command Mode

User EXEC Mode

User Guidelines

There are no user guidelines for this command.

Examples

The following example displays information about the active users.

Console> show users

Username Idle Time Remote IP Protocol

----------- --------- --------- ---------

Bob 00:00:00 Serial

Betty 00:08:19 172.16.0.1 Telnet

Robert - 172.16.0.8 HTTP


show clock

Use the show clock user EXEC command to display the time and date from the system clock.

Syntax

show clock

Default Configuration

This command has no default configuration.

Command Mode

User EXEC Mode

User Guidelines

There are no user guidelines for this command.

Examples

The following example displays the time and date from the system clock.

Console> show clock

15:29:03 Jun 17 2002


show system

Use the show system user EXEC command to display system information.

Syntax

show system [unit unit]

    • unit unit—Unit number. If unspecified, defaults to the master unit number.

Default Configuration

This command has no default configuration.

Command Mode

User EXEC Mode

User Guidelines

There are no user guidelines for this command.

Examples

The following example displays the system information.

Console> show system

System Description: Corporate

System Up Time (days,hour:min:sec): 1,22:38:21

System Contact:

System Name: Console 1

System location:

power supply status : OK

MAC Address: xxxx.xxxx.xxxx

Sys Object ID:


show version

Use the show version user EXEC command to display the system version information.

Syntax

show version [unit unit]

    • unit unit—Unit number. If unspecified defaults to the master unit number.

Default Configuration

This command has no default configuration.

Command Mode

User EXEC Mode

User Guidelines

There are no user guidelines for this command.

Examples

The following example displays a system version (this version number is only for demonstration purposes).

Console> show version

SW version x.xxx (date xx-xxx-xxxx time 17:34:19)

Boot version x.xxx (date xx-xxx-xxxx time 11:48:21)

HW version x.x.x

Unit SW version Boot version HW version

----- ---------- ------------ ------------

1 3.131 2.178 1.0.0

2 3.131 2.178 1.0.0


show system id

Use the show system id user EXEC command to display the system identification information.

Syntax

show system id [unit unit]

    • unit unit—Unit number. If unspecified, defaults to the master unit number.

Default Configuration

This command has no default configuration.

Command Mode

User EXEC Mode

User Guidelines

The tag information is on a device by device basis.

Examples

The following example displays the system identification information.

Console> show system id

Service Tag: 89788978

Serial number: 8936589782

Asset tag: 7843678957


Back to Contents Page

 

Notebooks | Computadores | Notebooks para Empresas | Computadores para Empresas | Workstations | Servidores | Armazenamento | Monitores | Acessórios
Direitos Autorais 1999-2009 Dell Inc.
Termos de Uso do Site | Problemas Não Resolvidos | Termos de Venda | Política de Privacidade | Sobre a Dell | Programa de Afiliados | Reciclagem Dell |Fale Conosco | Mapa do site | Feedback

Ofertas limitadas, por linha de produto, a 03 unidades para pessoa física, seja por aquisição direta e/ou entrega a ordem, e que não tenha adquirido equipamentos Dell nos últimos 04 meses, e 05 unidades para pessoa jurídica ou grupo de empresas com até 500 funcionários registrados. Os serviços de suporte pós-garantia e/ou outros serviços serão faturados em nota fiscal específica de prestação de serviços. Valores com frete não incluso. Preços com impostos para a cidade de São Paulo. Preços e condições serão válidos desde que não haja mudança, até a data de emissão da nota fiscal, da carga tributária, de preços de insumos, da cotação PTAX/BACEN do dólar norte-americano da data de conclusão do pedido, superior a 3% para insumos importados, ou outros fatores fora do controle da Dell. Clique aqui e obtenha maiores informações sobre as condições de pagamento. A partir de 01 de setembro de 2009 a Dell Computadores do Brasil emitirá a Nota Fiscal Eletrônica. Clique aqui para mais detalhes.

Promoção válida somente para a oferta anunciada e para as 100 primeiras unidades vendidas.

Em até 3 dias úteis contados do recebimento do pedido de compra on-line pela Dell, o cliente receberá um e-mail confirmando as condições de seu pedido. A Dell se reserva o direito de rever/corrigir o preço e as demais condições do negócio, comunicando ao cliente essa retificação, o qual, se não quiser manter o pedido nessa hipótese, deverá informar a Dell em até 5 dias úteis contados do recebimento da comunicação de retificação. A Dell reserva-se o direito de não concluir a venda se os equipamentos forem adquiridos para revenda.

Garantia: Garantia legal inclusa no prazo total de garantia. A garantia limitada inclui peças e mão-de-obra, sendo restrita aos produtos Dell. Os produtos de outras marcas estão sujeitos aos termos de garantia dos respectivos fabricantes. Na Garantia em Rede Autorizada, o serviço padrão é de 01 ano (incluída a garantia legal), em que o cliente, após contato telefônico com o Suporte Técnico da Dell, deverá encaminhar o seu equipamento à assistência técnica autorizada mais próxima de sua residência ou encaminhar pelos Correios, sem ônus, desde que seja guardada a caixa original do produto. Clique aqui para mais detalhes. Na Garantia à Domicílio, técnicos serão deslocados, se necessário, após consulta telefônica. O tempo de resposta dependerá da sua região geográfica e da disponibilidade imediata de recursos. Consulte o seu representante de vendas em caso de dúvida sobre qual é a garantia do seu equipamento.  Baterias de notebooks têm garantia de 1 ano. Lâmpadas dos projetores têm garantia de 90 dias. Para maiores detalhes clique aqui. A Dell não fornece garantia nem suporte técnico para FreeDOS™ nem qualquer outro sistema operacional ou aplicativo que não tenha sido instalado pela própria Dell nos computadores n Series. A Dell não garante a compatibilidade entre qualquer sistema operacional e os sistemas n Series. Para maiores informações sobre a Política de Devoluções da Dell clique aqui.

CompleteCare: Serviço de assistência técnica opcional, que cobre manutenção e substituição em caso de danos acidentais não cobertos pela garantia limitada, incluindo derramamentos, quedas, aumentos na tensão e quebra, e excluindo danos causados por atos intencionais, como fogo, roubo e perda clique aqui.

Wireless: Para a utilização da conectividade sem fio ("wireless") é necessária a aquisição de um roteador "wireless" e do serviço de banda larga no local de acesso ou da disponibilidade deste serviço em locais públicos.

Os softwares ofertados estão sujeitos aos Termos e Condições da Licença de Uso do Fabricante. Para maiores informações, consulte o site do fabricante.

Celeron, Celeron Inside, Centrino, Logotipo Centrino, Core Inside, Intel, Logotipo Intel, Intel Core, Intel Inside, Logotipo Intel Inside, Intel Viiv, Intel vPro, Itanium, Itanium Inside, Pentium, Pentium Inside, Xeon, e Xeon Inside são marcas registradas da Intel Corporation nos Estados Unidos e em outros países.

©2009 Advanced Micro Devices, Inc. Todos os direitos reservados. A sigla AMD, o logotipo de seta da AMD e as combinações resultantes disso são marcas registradas da Advanced Micro Devices, Inc. Outros nomes têm apenas propósitos informativos e podem ser marcas registradas dos seus respectivos proprietários.

Microsoft e Windows são marcas registradas da Microsoft Corporation nos EUA.

Empresa beneficiada pela Lei de Informática.

Fotos meramente ilustrativas

© 2009 Dell Inc. Todos os direitos reservados.

snWEB4