Back
to Contents Page
DSL Modem Connection
|
|
NOTE:
|
It
is recommended that you install the Dell Wireless 2350 Broadband Router using the Setup Wizard
provided on the Dell Wireless 2350 Broadband Router CD. Perform the steps below only when you are
unable to install the Dell Wireless 2350 Broadband Router with the Setup Wizard.
|
|
|
NOTE:
|
PPPoE
(Point to Point Protocol over Ethernet) is the methodology of authenticating
or validating a user or equipment to an Internet service provider, usually via
a username and/or password. It is a selection or action that reconfigures a
device to the default parameters, as it was originally manufactured.
|
DSL
without PPPoE - Standard Setup
Use this setup
when your DSL service provider does not ask you to enter any information for
your Internet connection.
DSL
with PPPoE
Use this setup if
your ISP has given you a username and password for your Internet connection.
1.
Connect
the Ethernet port on the DSL modem to the Internet port on the
Dell Wireless 2350 Broadband Router through an Ethernet cable.
2.
Connect
any one of the four LAN ports on the Dell
Wireless 2350 Broadband Router to the Ethernet
port on your computer through another Ethernet cable.
3.
Turn
on the Dell
Wireless 2350 Broadband Router.
4.
The
setup should work on the Dell
Wireless 2350 Broadband Router with the factory default settings.
|
|
NOTE:
|
If
the installation is not successful because you have modified any setting or
due to other factors, you can restore the default settings by pressing the Reset
button on the back of the Dell Wireless 2350 Broadband Router for at least 5 seconds. The
Dell Wireless 2350 Broadband Router will reboot with the default settings and the setup should
complete at this point.
|
|
|
NOTE:
|
The
Dell Wireless 2350 Broadband Router is configured by default with the following settings:
�
The
cable/DSL interface is configured with the DHCP client enabled. This means it
will try and get its Internet IP address automatically from your ISP.
�
The
Local Area Network and Wireless interfaces are configured with the DHCP
server enabled. This means that the Dell Wireless 2350
Broadband Router will allocated IP addresses to any connect computer
automatically.
�
Default
user name and password is admin. Use this to access the Configuration
Settings on the Dell Wireless 2350
Broadband Router when you browse to http://my.router
This
configuration will work properly with a DSL provider that does not
require authentication.
|
Back
to Top
1.
Connect
the Ethernet port on the cable modem to the Internet port on the Dell Wireless 2350
Broadband Router
through an Ethernet cable.
2.
Connect
any one of the four LAN ports on the Dell Wireless 2350
Broadband Router
to the Ethernet
port on your computer through another Ethernet cable.
3.
Turn
on the Dell Wireless 2350
Broadband Router.
4.
Open
your web browser (for example Internet Explorer) and go to http://my.router,
or the default IP address http://192.168.2.1.
5. Enter the
default username and password admin when prompted to do so.
6.
Go
to the Basic Settings
menu option tab on the top navigation bar and wait for the menu to appear.
7.
Click
the Internet Connection Settings menu option on the pull down menu.
8.
Select
Connection Type from the drop down menu and select DSL(PPPoE).
9.
Type
the user name provided to you by your ISP in the User Name box.
10. Type
your password in the Password and Retype Password boxes.
11. If your ISP requires you to
provide a MAC address, click to check the Your ISP requires you to
input WAN Ethernet Mac box.
11. Type the address in the
appropriate box.
12. Click the Next
button.
13. Click the Save &
Restart button.
14. When your web browser
returns to the main page of the network, the Dell Wireless 2350
Broadband Router will have successfully
restarted with the new settings.
Back
to Top
Back
to Contents Page
