The 2209WA flat panel display has an active matrix, thin-film
transistor (TFT), liquid crystal display (LCD). The monitor features include:
■ 22-inch (573.6 mm) viewable area display (Measured diagonally) .
■ 1680 x 1050 resolution, plus full-screen support for lower
resolutions.
■ Wide viewing angle to allow viewing from a sitting or standing position, or
while moving from side-to-side.
■ Tilt, swivel, vertical extension and rotate adjustment capability.
■ Removable pedestal and Video Electronics
Standards Association (VESA) 100 mm mounting holes for flexible mounting
solutions.
■ Plug and play capability if supported by your system.
■ Retractable label card allows convenient access to monitor serial number for technical support and easily hidden away providing label-free clean look.
■ On-Screen Display (OSD) adjustments for ease of set-up and screen
optimization.
■ Software and documentation media includes an information file (INF), Image
color Matching File (ICM), and product documentation.
■ Energy Saver feature for Energy Star compliance.
■ Security lock slot.
■ Asset Management Capability.
■ Capability to switch from wide aspect to standard aspect ratio while maintaining the image quality.
NOTE: Monitor shipped with label card fully inserted in USB compartment. Pull out the label card to access the barcode serial number label and regulatory rating label.
Connect the power cord for the soundbar (optional)
3
DVI connector
Connect your computer DVI cable
4
VGA connector
Connect your computer VGA cable
5
USB upstream port
Connect theUSB cable that came with your monitor to the monitor and the computer. Once this cable is connected you can use the USB connectors on the side and bottom of the monitor.
6
USB downstream ports
Connect your USB devices. You can only use this connector after you have connected the USB cable to the computer and USB upstream connector on the monitor.
Analog RGB, 0.7 Volts +/- 5%, positive
polarity at 75 ohm input impedance
Digital DVI-D TMDS, 600mV for each differential line, positive
polarity at 50 ohm input impedance
Synchronization input signals
Separate horizontal and
vertical synchronizations, polarity-free TTL level, SOG (Composite
SYNC on green)
If you have VESA's DPM™ compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. This is referred to as
Power Save Mode*. If the computer detects input from keyboard, mouse, or other input devices,
the monitor automatically resumes functioning. The following table shows the power consumption and signaling of this automatic power saving feature:
VESA Modes
Horizontal Sync
Vertical Sync
Video
Power Indicator
Power Consumption
Normal operation
Active
Active
Active
Blue
52 W (typical)
Active-off mode
Inactive
Inactive
Blanked
Amber
Less than 1 W
Switch off
-
-
-
Off
Less than 1 W
The OSD will only function in the normal operation mode. When the
menu or plus buttons are pressed in Active-off mode, one of the
following messages will be displayed:
Analog Input In Power Save Mode.
Press Computer Power Button
or Any Key on Keyboard or Move Mouse
OR
Digital Input In Power Save Mode.
Press Computer Power Button
or Any Key on Keyboard or Move Mouse
Activate the computer and the monitor to gain access to the
OSD.
NOTE: This monitor is ENERGY STAR®-compliant as well as TCO '03 power management compatible.
* Zero power consumption in OFF mode can only be achieved by disconnecting the main cable from the monitor.
You can install the monitor in any Plug and Play-compatible system. The monitor automatically provides the computer system with its Extended Display Identification Data (EDID) using Display Data Channel (DDC)
protocols so the system can configure itself and optimize the monitor settings. Most monitor installations are automatic; you can select
different settings if desired. For more information about changing the monitor
settings, see Operating the Monitor.
This section gives you information about the USB ports that are available on the left side of your monitor.
NOTE: This monitor supports High-Speed Certified USB 2.0 interface
Transfer speed
Data Rate
Power Consumption
High speed
480 Mbps
2.5W (Max., each port)
Full speed
12 Mbps
2.5W (Max., each port)
Low speed
1.5 Mbps
2.5W (Max., each port)
USB Upstream Connector
Pin Number
4-pin Side of the Connector
1
DMU
2
VCC
3
DPU
4
GND
USB Downstream Connector
Pin Number
4-Pin Side of the Signal Cable
1
VCC
2
DMD
3
DPD
4
GND
USB Ports
1 upstream - back
4 downstream - 2 on back; 2 on left side
NOTE: USB 2.0 functionality requires a USB 2.0-capable computer
NOTE: The monitor's USB interface works only when the monitor is on or in power save mode. If you turn off the monitor and then turn it on, the attached peripherals may take a few seconds to resume normal functionality.
LCD Monitor Quality and Pixel Policy
During the LCD Monitor manufacturing process, it is not uncommon for one or more pixels to become fixed in an unchanging state which are hard to see and do not affect the display quality or usability.For more information on Dell Monitor Quality and Pixel Policy, see Dell Support site at:
support.dell.com.
CAUTION: Read and follow the safety
instructions before cleaning the monitor.
CAUTION: Before cleaning the monitor, unplug the monitor
power cable from the electrical outlet.
For best practices, follow the instructions in the list below while
unpacking, cleaning, or handling your monitor:
To clean your antistatic screen, lightly dampen a soft, clean cloth with
water. If possible, use a special screen-cleaning tissue or solution
suitable for the antistatic coating. Do not use benzene, thinner, ammonia, abrasive cleaners, or compressed
air.
Use a lightly-dampened, warm cloth to clean the monitor. Avoid using detergent of any
kind as some detergents leave a milky film on the monitor.
If you notice white powder when you unpack your monitor, wipe it off with
a cloth.
Handle your monitor with care as a darker-colored monitor may scratch and
show white scuff marks more than a
lighter-colored monitor.
To help maintain the best image quality on your monitor,
use a dynamically changing screen saver and turn off your monitor
when not in use.
