Dell Soundbar power connector - Connect the
power cord for the Soundbar (optional)
3.
DVI connector - Connect your computer DVI
cable
4.
VGA connector - Connect your computer VGA cable
5.
USB upstream connector - Connect the USB cable that came with
your monitor to the monitor and the computer. Once this cable is
connected you can use the USB connectors on the side and bottom of the
monitor.
6.
USB connector - Connect your USB devices. You can only use this
connector after you have connected the USB cable to the computer and
USB upstream connector on the monitor.
If you have VESA's DPM™ compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. This is referred to as 'Power Save Mode'*. If input from keyboard, mouse or other input devices is detected by the computer, the monitor will automatically "wake up". The following table shows the power consumption and signaling of this automatic power saving feature:
VESA Modes
Horizontal Sync
Vertical Sync
Video
Power Indicator
Power Consumption
Normal operation( with Dell Soundbar
and USB active)
Active
Active
Active
Green
65 W (maximum)
Normal operation
Active
Active
Active
Green
32 W (typical)
Active-off mode
Inactive
Inactive
Blanked
Amber
Less than 3 W
Switch off
-
-
-
Off
Less than 1 W
NOTE: The OSD will only function in the 'normal operation' mode.
Otherwise one of the following messages will appear when the “menu” or
“plus” buttons are pressed when in Active-off mode.
1. Analog Input
In Power Save Mode
Press Any Key on Keyboard or Move Mouse
or
2. Digital Input
In Power Save Mode
Press Any Key on Keyboard or Move Mouse
Activate the computer and 'wake up' the monitor to gain access to the
OSD.
This monitor is ENERGY STAR®-compliant as well as TCO
'99 / TCO '03 power management compatible.
* Zero power consumption in OFF mode can only be achieved by disconnecting the main cable from the monitor.
ENERGY STAR® is a U.S. registered mark. As an ENERGY STAR® Partner, DELL has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.
This monitor supports High-Speed Certified USB 2.0 interface.*
Data Rate
Power Consumption
High speed
480 Mbps
2.5W (Max., each port)
Full speed
12 Mbps
2.5W (Max., each port)
Low speed
1.5 Mbps
2.5W (Max., each port)
USB ports:
1 upstream - rear
4 downstream - 2 on rear; 2 on left side
NOTE: USB 2.0 capability
requires 2.0 capable computer
NOTE: Monitor's USB interface works ONLY when monitor is Powered ON
(or in Power Save Mode). Switching your monitor OFF and then ON would re-enumerate its USB
interface; attached peripherals may take a few seconds to resume normal functionality.
You can install the monitor in any Plug and Play-compatible system. The monitor automatically provides the computer system with its Extended Display Identification Data (EDID) using Display Data Channel (DDC) protocols so the system can configure itself and optimize the monitor settings. If desired, the user can select different settings, but in most cases monitor installation is automatic.
Analog RGB, 0.7 Volts +/-5%, positive polarity at 75 ohm input impedance
Digital DVI-D TMDS, 600mV for each differential line, positive polarity at 50 ohm input impedance
Synchronization input signals
Separate horizontal and vertical synchronizations, polarity-free TTL level, SOG (Composite SYNC on green)
CAUTION: Read and follow the safety
instructions before cleaning the monitor.
CAUTION: Before cleaning the monitor, unplug the monitor
from the electrical outlet.
To clean your antistatic screen, lightly dampen a soft, clean cloth with
water. If possible, use a special screen-cleaning tissue or solution
suitable for the antistatic coating. Do not use benzene, thinner, ammonia, abrasive cleaners, or compressed
air.
Use a lightly-dampened, warm cloth to clean the plastics. Avoid using detergent of any
kind as some detergents leave a milky film on the plastics.
If you notice a white powder when you unpack your monitor, wipe it off
with a cloth. This white powder occurs during the shipping of the monitor.
Handle your monitor with care as darker-colored plastics may scratch and
show white scuff marks more than
lighter-colored monitor.
