| Back to Contents Page |
Using Your Projector: Dell™ 3200MP Projector
|
 Control
Panel
Remote Control
On-Screen Display
|
Control Panel
|
| Power |
| See "Powering On/Off the
Projector." |
Source |
Press  to step through Analog RGB, DVI, Composite, Component-I, S-video,
and Analog YPbPr sources when multiple sources are connected to the projector. |
R-Sync (Resync) |
Press  to synchronize the projector to the input source.
R-Sync will not operate if the OSD is displayed. |
Menu |
Press 
to activate the OSD. An input signal is required to activate
the OSD. |
Four Directional Keys |
The four directional keys     can be used to toggle through the tabs
in the OSD. |
Keystone |
Press 
or 
button to adjust image distortion caused by tilting the projector. (±
30 degrees) |
|
Remote Control
- If the remote control cover is closed:
The R-Sync button functions as the right mouse button.
The Enter button functions as the left mouse button.
- If the remote control cover is open, use the directional pad to navigate
through the OSD tabs.
 
| 1 |
Directional pad |
| 2 |
Enter button |
| 3 |
Laser radiation caution |
|
Power |
| See "Power On/Off the Projector." |
Source |
| Press the Source button to choose
Analog RGB, DVI, Composite, Component-I, S-video, and Analog YPbPr sources. |
R-Sync |
If the remote control cover is open,
the R-Sync button synchronizes the projector to the input
source.
If the remote control cover is closed, the R-Sync button
functions as the right mouse button. |
Directional Pad |
| The directional pad can be used to control mouse
movement when the remote control cover is closed. The mouse function is
enabled using the USB connector on the M1-A to combination VGA and USB cable
between your computer and the projector. |
Laser |
| Aim the remote control at the screen, and press
and hold the Laser button to activate the laser light. |
Page Up |
| Press the PU button to page up. |
Page Down |
| Press the PD button to page
down. |
Menu |
| Press the Menu button to activate
the OSD. Use the directional pad and Enter button to navigate
through the OSD. |
Zoom In/Out |
| Press the In button
to digitally magnify an image up to 32 times on the screen. Press the Out
button to reduce the zoomed image. |
Freeze |
| Press the Freeze button to temporarily
stop motion video. Press the button again to resume . |
Mute |
| Press the Mute button to mute or unmute the
projector speaker. |
Volume |
| Increases/decrease the speaker volume. |
Keystone |
| Adjusts image distortion caused by tilting the projector.
( ± 30 degrees) |
Enter |
| Activates the left mouse button when the remote control cover
is closed. |
On-Screen Display
|
- The projector has a multi-language OSD that can only be displayed
when an input source is present.
|
- The OSD allows you to make image adjustments and change a variety
of settings. If the source is a computer, the OSD allows changes to
the computer OSD. When using a video source,
the OSD allows changes to the video OSD.
The projector automatically detects the source.
|
- When the OSD is on the screen, press or
to navigate through the OSD tabs.
Example: All Images--> Computer Image--> Audio--> Management-->
Language--> Factory Reset. To make a selection in a tab, press .
|
- Press or
to make a selection and adjust the
settings by pressing
or on key pad or
"Left" and "Right" button on the remote controller. When an item is
selected, the color of the item changes from light blue to dark blue.
|
- To exit the OSD, press
button on keypad or "Enter" button on the remote controller.
All Images Menu
|
|
|
-
|
|
|
|
|
-
|
Color Temp. |
|
Adjusts the color temperature. With the higher temperature, the
screen looks colder; with the lower temperature, the screen looks
warmer. User mode activates the values in the "color setting"
menu.
|
|
-
|
Color Setting |
|
This mode allows for manual adjustment of red, green, and blue
color settings. Modifying these values will automatically change
the color temperature to "user".
|
|
-
|
Keystone |
|
Adjusts image distortion caused by tilting the projector. (±
30degrees)
|
|
|
|
| |
Aspect Ratio |
|
Select this function to fit 1:1, 16:9 or 4:3 aspect ratio. The
input must be a computer signal (through M1-A to VGA cable) less
than XGA (1024 x 768), component 576p/ 480i / 480p, S-Video, or
Video (composite). If the input signal is a computer signal greater
than XGA or component 1080i / 720p, only 16:9 or 4:3 aspect ratio
will be available. When an icon is selected, the color of the icon
will change to dark blue.
|
|
-
|
White Intensity |
|
White Intensity can be adjusted between
0 and 10. |
|
- Setting 10 will maximize the brightness.
- Setting 0 will maximize color reproduction quality.
|
Audio Menu
|
|
|
|
|
| Audio |
|
|
-
|
Treble |
|
Control the higher frequencies of your audio source.
- Press
to decrease the treble.
- Press
to increase the treble.
|
|
|
|
-
|
Mute |
|
- Select the left icon to mute the volume.
- Select the right icon to unmute the volume. .
|
|
|
Management Menu
|
|
|
|
|
| Management |
-
|
Menu Location |
|
Select the location of the OSD on the screen.
|
|
|
|
-
|
Signal Type |
|
Manually select signal type RGB, YCbCr, YPbPr.
|
|
-
|
Lamp Hour |
|
Displays operating hours since lamp timer reset.
|
|
-
|
Lamp Reset |
|
Use this function only after a new lamp is installed in the projector.
Select the left Lamp Reset icon (light bulb and
arrow under the icon), and press the Enter button
to reset the lamp timer.
|
|
|
Power Saving Menu
|
Power Saving
|
|
Use this function to select the power saving delay
period. Press "Yes" to go into the "set time" sub menu. |
| |
-
|
Set Time(Min) |
|
Set the power saving delay period as you prefer. When the projector
is not receiving an input signal for the selected period of time,
the projector will automatically enter power saving mode, and turn
off the lamp. After a one-minute cooling period, the projector will
turn back on with detection of an input signal or by pressing the
"Power" button.
|
|
|
Language Menu
|
|
|
| Language |
-
|
Language |
|
Press
or to select the language
you prefer. |
|
|
Factory Reset Menu
|
|
|
|
|
|
-
|
Factory Reset |
|
Select Yes to reset the
projector to its factory default settings. Reset items include both
computer image and video image settings. |
|
|
Computer Image Menu
|
|
|
|
|
|
Computer Image- Note: this menu is only available with computer input
signal.
|
-
|
Frequency |
|
Change the display data frequency to match the frequency of your
computer graphic card. If you experience a vertical flickering bar,
use the frequency function to make an adjustment.
|
|
-
|
Tracking |
|
Synchronize the signal timing of the display with that of the graphic
card. If you experience an unstable or flickering image, use the
tracking function to correct it.
|
|
|
|
|
|
|
Video Image Menu
|
|
|
|
|
| Video Image- Note: this menu is only available with S-video,
video(composite) or component 480i signal. |
-
|
Color Saturation |
|
Adjust a video image from black and white to fully saturated color.
- Press
to decrease the amount of color in the image.
- Press
to increase the amount of color in the image.
|
|
-
|
Sharpness |
|
Adjust the sharpness of the image.
- Press
to decrease the sharpness.
- Press
to increase the sharpness.
|
|
-
|
Tint |
|
Adjust the color balance of red and green.
- Press
to increase the amount of green in the image.
- Press
to increase the amount of red in the image.
|
|
Back to Contents Page
|
Front Projection-Desktop 
Rear Projection-Desktop
Front Projection-Ceiling Mount
Rear Projection-Ceiling Mount
